Menu
Whirlpool W11411645A Quick Start Manual
         |
1FFrreenncchh DDoooorr BBoottttoomm MMoouunntt DDiissppeennssiinngg aanndd SSttoorraaggee GGuuiiddeeWater and Ice Dispenser ControlsA. Ice/Water dispenser paddlePress Ice/Water to toggle through the following choices in acontinuous loop:� Water (default) - Dispenses water.� Cubed - Dispenses cubed ice.� Crushed - Dispenses crushed ice.TO DISPENSE WATER (STANDARD)1. Select water.2. Press a sturdy glass against the water dispenser paddle.NOTE: While dispensing water and for 3 seconds afterdispensing has stopped, the digital display will show how muchwater has been dispensed.3. Remove the glass to stop dispensing.TO DISPENSE WATER (MEASURED FILL)Measured Fill allows you to dispense a specified amount of waterwith the touch pad.NOTE: The amount of water you select will be dispensed. Be surethat the container is empty and can hold the entire volume. If ice isin the container, you may need to adjust your selection.Household water pressure may affect the accuracy of theMeasured Fill feature. For optimum performance of your waterdispenser, you must first calibrate Measured Fill. For best results,calibration should be performed when water is not being used inthe house.How to calibrate Measured Fill:IMPORTANT: Flush the water system before calibrating MeasuredFill.1. Place a sturdy measuring cup (1-cup [237 mL] size) on thedispenser tray centered in front of the ice/water dispenserpaddle.NOTE: Depending on your model, a measuring cup may beprovided.2. Press and hold the Options and Lock buttons at the same timefor 3 seconds. The words “Back” and “1 Cup” will appear on thedisplay screen. Also, the Calibrate Measured Fill icon willilluminate and remain lit while the Measured Fill feature is beingcalibrated.NOTE: You may press Ice Type “Back” at any time to exitcalibration mode. The Calibrate Measured Fill icon will disappear.3. Press and release the water dispenser paddle, as needed, todispense water to the 1 cup fill line.NOTE: If overfilling or spilling occurs, discard the water andpress “Back” to restart the calibration process.4. Press Measured Fill to turn on the feature. When the feature ison, the Measured Fill screen appears on the display.When Measured Fill calibration has been confirmed, theCalibration icon will disappear and the display will return to thehome screen.1. Press Measured Fill to turn the feature on. When the feature ison, the Measured Fill screen appears on the display. Press Ice/Water “Back” to manually turn off the Measured Fill feature.NOTE: The dispenser will automatically turn off Measured Fillafter 1 minute of inactivity. When Measured Fill is turned off,any changes you have made will be lost and all defaults will berestored.2. You can dispense water by the ounce, cup, or liter. The defaultunit is ounces. To switch to cups or liters, press the Lightbutton.Default, minimum, and maximum volumes are listed below.Units Default Minimum MaximumOunces 8 1 128Cups 1 1/4 16Liters 0.25 0.05 4.003. Press the Lock and Options buttons to adjust the volume asdesired. The Lock button increases the volume, and theOptions button lowers the volume.NOTE: Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]per cup) are not the same size as a measuring cup (8 oz [237mL]). You may need to adjust the volume to avoidunintentionally overfilling coffee cups.When increasing or decreasing the dispense volumes, if anadjustment button (-/+) is held for approximately 10 seconds orlonger the control may stop responding. Release the button forapproximately 2 seconds and then continue making theadjustment. |
Related manuals for Whirlpool W11411645A
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved