Menu
Whirlpool AKT 933 Instruction Manual
    |
ELECTRICAL CONNECTIONIMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.ASSEMBLYADJUSTMENT TO DIFFERENT TYPES OF GASIf the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information labelon the top of the hob, change the injectors.Remove the information label and keep it with the instructions booklet.Use pressure regulators suitable for the gas pressure indicated in the Instruction.• The gas nozzles must be changed by After Sales Service or a qualified technician.• Nozzles not supplied with the appliance must be ordered from After Sales Service.• Adjust the minimum setting of the taps.NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service forthe replacement of the burner tap if found to be faulty.REPLACING THE INJECTORS (see the injector table in the Instruction)ADJUSTING MINIMUM GAS SETTING OF TAPSREFERENCE TO LOCAL REGULATIONSProvision for ventilationThe room in which the appliance is installed must have an air supply to current B.S. 5440 - Part 2 standards.All rooms require a permanent vent in addition to the openable window.If there are other fuel burning appliances in the same room B.S. 5440 - Part 2 should be consulted to determine the air ventrequirements.If the appliance is installed in a cellar or basement, it is advisable to provide an air vent of 65 cm, irrespective of the roomvolume.Gas Safety RegulationsThe law requires that all gas appliances are installed by competent persons in accordance with the current gas safetyregulations. Failure to install appliances correctly may lead to prosecution.It is in your own interest, and that of safety, to ensure that the law is complied with. The hob should be installed in accordancewith the Gas Safety (Installation and Use) Regulations, the Building Regulations issued by the Department of theEnvironment and the Building Standard (Scotland) (Consolidation) Regulations, issued by the Scottish DevelopmentDepartment.In the G.B., CORGI registered installers work to safe standards of practice.AFTER-SALES SERVICEWARNING This operation must be performed by a qualified technician.WARNING • The electrical connections must complywith local regulations.• The earthing of this appliance iscompulsory by law.• Do not use an extension cord.After having cleaned the perimeter surface,apply the supplied gasket to the hob as shownin the figure.Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.NOTE: the power supply cable must be long enough to permit its upward extraction.To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow andfasten them by means of their screws in accordance with the thickness of the worktop (see the following figures).WARNING This operation must be performed by a qualified technician.LNEarth(yellow/green)20306040Top 20 mm Top 40 mmTop 30 mm Top 60 mmNO• Remove grids (A).• Extract burners (B).• Using a socket spanner of the appropriate size unscrewthe injector (C), unscrew the injector to be replaced.• Replace it with the injector suitable for the new type ofgas.• Re-assemble the injector in (D).• If you have a multiple crown burner use side spanner toreplace the injector (E).Before installing the hob, remember to affix the gascalibration plate supplied with the injectors in such a waythat it covers the existing information relating to gascalibration.To ensure that the minimum setting is correctly adjusted, remove the knob and proceedas follows:• tighten screw to reduce the flame height (-);• loosen screw to increase the flame height (+).The adjustment must be performed with the tap in minimum gas setting position (smallflame) .• The primary air of the burners does not need to be adjusted.• At this stage, light up the burners and turn the knobs from max position tominimum position to check flame stability.Upon completion of adjustment, reseal using sealing wax or an equivalent material.Before calling the After-Sales Service, make sure you can give the following information:- type of fault or problem;- exact model (written on the label affixed to the instruction/warranty);- service number that follows the word SERVICE on the rating plate under the hob andon the label affixed to instruction/warranty;- your complete address and phone number.If any repairs are required, please contact an authorised After-Sales Service, as indicated in thewarranty.IE |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved