Warmtech T510 Installation Manual

Warmtech T510 Installation Manual Manual pdf 1 page image

WARMTEC T510 Weekly Programming Thermostat with LCD Screen Installation ManualWARMTEC T510 Weekly Programming Thermostat with LCD Screen Installation ManualT510. Weekly Programming Thermostat with LCD ScreenWeekly circulation, it is possible to set 6 periods called events each day withdifferent temperatures, also you can select "manual mode" or "temporarycontrol mode" according to your individual requirements. The thermostat isrecommended for the control of electric heating devices or on/off valve actuatorused in water-based heating systems.Selection Table:Model Current ApplicationT510 16A Built-in & floor sensor, floor limit sensor, periodprogrammingT510i 16A A pair of contacts for potential- free outputTechnical data:Voltage : AC230V (AC110V/AC24V available)Power consumption : 2WSetting range : 5℃~90℃Limitation range : 5℃~99℃ (factory setting: 35℃)Switching differential :0.5℃~10℃ (factory setting: ±1℃)Ambient temperature : -5℃~50℃Protective housing : IP20Housing material : self-extinguishing PCDaily use of the thermostat1） on/off " "2） In the manual mode，press " " or" "to make temporary control。3） Press" " or" " to increase or decrease pre-set temperature.4） Press" " and" "and hold for 5 seconds at the same time to adjusttime. Press " " to choose object to adjust; Press" " or" " toincrease or decrease your set values; Press " " to confirm and exit.5） Press the " " key to select manual mode or clock-controlled programmode.6） It displays the time or the pre-set temperature alternately, and it displaysthe measured temperature directly.7） When you press " " and" "at the same time and hold for 5 seconds,the thermostat will be locked/unlocked. When it is locked, no operationcan be carried out until it is unlocked.Display symbols：Manual modePeriod control modeHeatingGetting up, the first periodOut in the morning, the second periodGoing home at noon, the third periodOut in the afternoon, the forth periodGoing home in the evening, the fifth periodSleeping at night, the sixth periodPeriod programmingPress " " and hold for 5s to enter the mode of Period programming.Key Period Symbol Time Temperatureweekday1 06:00Set the start/end time20℃Set programmed temperature2 08:00 15℃3 11:30 15℃4 12:30 15℃5 17:00 22℃6 22:00 15℃weekend 1 08:00 22℃2 23:00 15℃Advanced setting (qualified person preferred)When the thermostat is turned off, You can press" " and turn on it at the sametime ,then you can enter the mode of advanced setting.Symbol Setting or1 ADJ TemperaturecalibrationAdjust measured temperature2 SEN Sensor mode IN: built-in sensorOUT: floor sensorALL: both sensors3. LIT LimitationtemperatureAdjust limitation value,Limitation range:5℃~60℃4 DIF SwitchingdifferentialAdjust switching differential5 LTP AntifreezefunctionTurn on/off Anti-frozenfunction6 PRG Set vacationmode00: 5/2 day mode01: 6/1 day mode02: 7 day mode7 RLE Potential- freeoutput and mainpower output inthesame/differentwayChange the presentlinkage way8 DLY Delay time ofPotential- freeoutputChange linkage delay time9 HIT Max temperature Limitation temperaturesetpointAFAC Reset to factorysettingsPress" "and hold for 5s，allparameters will be resetSensor failure:Please select the right sensor mode when operation, it will display the"Err" symbol on screen far sensor failure, thermostat must be checked tillthe fault is eliminatedExplanation of symbols:Period modeAntifreezetemperatureLock keyheatingpowerNTCDecrease keyIncrease keyMenuWeekTimeSix periodManual modeDimension:Unit: mm86861343All manuals and user guides at all-guides.comall-guides.com

/ 2

Related manuals for Warmtech T510