Menu
W Box 0E-4CHNVR1TB Quick Setup Manual
Also see for 0E-4CHNVR2TB: User manual
  |
ComponentTable 2-1 Front panel descriptionNetwork video recorderSilicone cushionPower cordPower adapterMouseCD-ROMQuick Setup GuideFigure 2-1 Front panelPort Name DescriptionPoEIndicatorPoE network status indicatorThis indicator flashes when data is transmitted.1211111Phillips head screw 4Quantity RemarkPWRIndicatorWhen the NVR is operating, the PWR indicatoris steady on.When the NVR is shut down, thePWR indicator is turned off.Network Video Recorder(NVR)Quick Setup Guide0E-4CHNVR1TB0E-4CHNVR2TBFully understand this document before using this device, andstrictly observe rules in this document when using this device. Ifyou install this device in public places, provide the tip "You haveentered the area of electronic surveillance" in an eye-catchingplace. Failure to correctly use electrical products may cause fireand severe injuries.It alerts you to moderate dangers which, if notavoided, may cause minor or moderate injuries.It alerts you to risks. Neglect of these risks maycause device damage, data loss, deviceperformance deterioration, or unpredictable results.It provides additional information.Strictly observe installation requirements when installing thedevice. The manufacturer shall not be held responsible fordevice damage caused by users' non-conformance to theserequirements.Strictly conform to local electrical safety standards and usepower adapters that are marked with the LPS standard wheninstalling and using this device. Otherwise, this device may bedamaged.Use accessories delivered with this device. The voltage mustmeet input voltage requirements for this device.If this device is installed in places with unsteady voltage, groundthis device to discharge high energy such as electrical surges inorder to prevent the power supply from burning out.When this device is in use, ensure that no water or any liquidflows into the device. If water or liquid unexpectedly flows intothe device, immediately power off the device and disconnect allcables (such as power cables and network cables) from thisdevice.Do not focus strong light (such as lighted bulbs or sunlight) onPrecautionsNOTECAUTIONWARNINGWARNINGSpecial AnnouncementFor more information, please refer to CD (included), wboxtech.comor call W Box Tech Support 1-833-574-9124.Avoid heavy loads, intensive shakes, and soaking to preventdamages during transportation and storage. The warranty doesnot cover any device damage that is caused during secondarypackaging and transportation after the original packaging istaken apart.Protect this device from fall-down and intensive strikes, keep thedevice away from magnetic field interference, and do not installthe device in places with shaking surfaces or under shocks.Clean the device with a soft dry cloth. For stubborn dirt, dip thecloth into slight neutral cleanser, gently wipe the dirt with thecloth, and then dry the device.Do not jam the ventilation opening. Follow the installationinstructions provided in this document when installing the device.Keep the device away from heat sources such as radiators,electric heaters, or other heat equipment.Keep the device away from moist, dusty, extremely hot or coldplaces, or places with strong electric radiation.If the device is installed outdoors, take insect- and moisture-proof measures to avoid circuit board corrosion that can affectmonitoring.Remove the power plug if the device is idle for a long time.All complete products sold by the manufacturer are deliveredalong with nameplates, and accessories afterstrict inspection. The manufacturer shall not be held responsiblefor counterfeit products.The manufacturer will update this manual according to productfunction enhancement or changes and regularly update thesoftware and hardware described in this manual. Updateinformation will be added to new versions of this manual withoutprior notice.This manual may contain misprints, technology information thatis not accurate enough, or product function and operationdescription that is slightly inconsistent with the actual product,the final interpretation of company is as a standard.This manual is only for reference and does not ensure that theinformation is totally consistent with the actual product. Forconsistency, see the actual product.quick setup guideNOTEthis device. Otherwise, the service life of the image sensor maybe shortened.If this device is installed in places where thunder and lightningfrequently occur, ground the device nearby to discharge highenergy such as thunder strikes in order to prevent devicedamage.CAUTIONOpen the package, check the appearance of product for noobvious damage, and confirm the item for 1-1 isconsistent.list tableTable 1-1 Packing listOpen Package Examination12.1 Device Ports.NOTEDevice Structure22.2 Device DimensionsDifferent device may have different dimensions, please referto the .actual productNOTE3 Device InstallationFigure 2-3 Dimensions (Unit:mm)Figure 2-2 Rear panelName DescriptionGround screwPoE networkinterface PoE network interfacesSafe ground screw of the device12IDTable 2-2 Rear panel descriptionName DescriptionRESET Factory reset buttonLAN networkinterfaceRJ45 10 /100/1000 Mbps adaptiveEthernet interface3ID4 LINE OUT/LINE IN Audio output and audio input56HDMIVGA Video output interface7Alarm Alarm input and Alarm output8DC powerinterface Connected to an external power adapter9235255Depending on model, many W Box models already include a HardDrive installed. When a hard drive is not included or when addinghard drives please take the following steps to install hard disks.Step 1 Remove the screws for fixing the cover and take down thecover.Step 2 Take out the screws and silicone cushion, route the screwsthrough the silicone cushion, and install it to the screwholes, as shown in figure 3-1.Figure 3-1 Installing the hard disk screwsStep 3 Route the screws through the holes on the base, push thehard disk to the appropriate position on the left, as shown infigure 3-2.Turn the device over, and fasten the rest two hard diskfixing screws, as shown in figure 3-3.Step 4 During the installation, ensure that the large disc of the siliconcushion close to the hard disk screw holes. Please install the hard disk fixing screws on the screw holes faraway from the power supply interface.NOTEFigure3-2 Installing hard diskStep 5 Insert the hard disk data cable and power cable, then put onthe upper cover and fasten the fixing screws.Figure3-3 Fixing hard disk89.8Network Video RecorderKB/MOUSE BACKUPNetwork Video RecorderKB/MOUSE BACKUP2 4 7 831 5 6 9Different device may have different ports and multi-head cable,please refer to the actual product. |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved