Menu
Vantage Hearth LVOS-0-10-PWM-1 Installation Manual
Also see for LVOS-0-10-PWM-1: Installation
    |
©Vantage, 8/12/2016 / IS-0523-B Low Voltage Output Station, 0-10V & PWM – MODEL: LVOS-0-10-PWM-1 page 1 of 4I N S T A L L A T I O NV A N T A G E C O N T R O L S . C O M V A N T A G E I N S T A L L G U I D E S2168 West Grove Parkway, Suite 300, Pleasant Grove, UT. 84062 USATelephone: 801 229-2800 ● Fax: 801 224-0355 Low Voltage Output Station, 0-10V & PWM – MODEL: LVOS-0-10-PWM-1OverviewThe Vantage LVOS-0-10-PWM-1(LVOS) has four PWM and four analogLow Voltage Outputs along with fourhigh voltage relays. All twelveconnections are independent from eachother. The station is powered from auniversal input of 120-277 VAC50/60Hz source. The high voltagerelays are isolated from the station’s high voltage power supply. Alloutputs can be manually controlled and monitored from the front of thestation. An Override switch may be connected allowing all the low voltageloads and high voltage relays to be ON or OFF for fail-safe applications.The station comes housed in a custom metal enclosure or may be orderedseparately for installation into Vantage’s IAUX enclosure. Communicationto the Vantage System is via Ethernet or Station Bus.Two Ways to OrderPart Number DescriptionLVOS-0-10-PWM-1Station with Single Enclosure:Low Voltage Output Station (PWM and 0-10) 120v-277v – comes in a custom Vantage supplied, ULrated enclosureLVOS-0-10-PWM-P-1 LVOS-O-10-PWM station only – for installing in ULrated IAUX-2, IAUX-4, or LCAP series enclosures * .*WARNING: This is not a DIN station and is not designed for DIN rail.Vantage’s auxiliary enclosures, IAUX-2 / IAUX-4 and LCAP44A-6enclosures are ordered separately!Highlight Features 4 PWM, LV outputs 4 Analog, 0-10LV outputs 4 High Voltage Relays – tied to LV outputs in Design Center Twelve membrane style actuators and LED status indicators High Resolution Performance when Dimming Communicates via Vantage Ethernet Bus or Station Bus Housed in a custom, UL rated enclosureo part #LVOS-0-10-PWM-1 includes station and enclosure Enclosure configurationso IAUX-2 – up to six stations per enclosureo IAUX-4 – up to ten stations per enclosureo Override Switch connections for ON and OFF states of all loadscollectivelyStation SpecificationsGeneralWall BoxDimensions, HWD 9.0” x 10.5” x 2.75”22.86cm x 26.67cm x 6.98cmCoverDimensions, HWT 9.75” x 11.25” x 0.6” (1/16” Thick)24.77cm x 28.58cm x 15mm-thickStation OnlyDimensions, HWD 3.32” x 10.34” x 2.667”8.43cm x 26.26cm x 6.77cmWeight with box 5.85lbs -or- 2.65kgLED Indicators Microprocessor Status, Configuration, LoadsAmbient OperatingTemperature 32-104°F / 0-40°CRelative Humidity Maximum 90%, non-condensingCooling ConvectionFirmware Upgradeable via Ethernet or Station BusManual Control Overlay with control/status for each outputFreeRTOS™ Real-time scheduling provided by FreeRTOS(www.freertos.org)AC Input – Power SupplyType Universal InputInput voltage /frequency 120 – 277 VAC 50-60HzInput power <16WConnection type 0.20” pitch removable plugConnection rating 300V 10AInput / Output Connections (Low Voltage)Vantage EthernetBus Port (VEB)RJ45 – Auto Crossover Detection – 10 / 100Ferrite clamp included for Ethernetconnection only (see page 3)Station Busconnection 24V / 36V Station BusStation Bus WireSpecification2C, 16AWG / 1.31mm2, twisted, non-shielded, <30pF per foot. Separate aminimum of 12" / 30.5cm from other parallelcommunication and/or high voltage runs.Station Wiringconfiguration Daisy-chain/Star/BranchStation EquivalentInFusion 0.35W on IC-24 / 0.55W on IC-36Auxiliary Inputs 4 Dry Contacts, (3 and 4 may be for an IRReceiver and Light Sensor respectively)Override Inputs Yes – All ON or All OFF contactsLow Voltage Output: PWM LowSpecification IEC 60929 Annex ENumber of outputs 4Output voltage 12V (source only)Output current 100mA per channel, 400mA totalLoads Per Output 50@ 2.0mA per load (typical)Resolution > 1024 stepsDuty cycle Variable 0% to 99.9%Frequency 760HzConnection type 0.20” pitch removable plugConnection rating 300V 10AConnection Torque 4.4 inch poundsLow Voltage Output: 0-10VSpecification IEC 60929 Annex ENumber of outputs 4Output 0-10V @ 100mA sink or sourceExternal sourcevoltage Typical 10V / Maximum 20VLoads Per Output 50@ 2.0mA per load (typical)Resolution >1024 stepsConnection type 0.20” pitch removable plugConnection rating 300V 10AConnectionTorque 4.4 inch poundsHigh Voltage Output: RelaysNumber of relays 4Voltage rating 120V-277 VACType Normally openLoad rating,general purpose 10ALoad rating,incandescent 5AElectronic Ballast 5ARelay inputconnected to linefeed NoConnection type 0.20” pitch removable plugConnection rating 300V 10AConnectionTorque 4.4 inch poundsProtectionHigh voltage input, overvoltage protection MOVLow voltage 0-10V outputover current protection PTC Fuse (self resetting)Low voltage PWM outputover current protectionCertificationsULListed 508CE,FCC Part15,Sub-PartBEN55022 Radiated / Conducted emissionsEN55024 61000-4-2 ESD immunityEN55024 61000-4-3 Radiated immunityEN55024 61000-4-4 Fast transient immunityEN55024 61000-4-5 Surge immunityEN55024 61000-4-6 Conducted immunityEN55024 61000-4-8 Magnetic field immunityEN55024 61000-4-11 Voltage dips/interruption immunity61000-3-2 Harmonics current emissions610000-3-3 Flicker emissionsPWM Outputs, 12V (Source)Low voltage outputs 1-4 may be configured as PWM (Pulse WidthModulation). PWM Duty Cycles are programmed using Power Profilesfrom 0%-Minimum On to 100%- Maximum On (99.9% actual). The loadlevel is a percentage between the minimum and maximum duty cycle(Power Profile Minimum On and Maximum On). The output can bereversed in Design Center through the Power Profile. For example, a0% duty cycle can either be load ON or load OFF.Low Voltage Outputs, 0-10V (analog)Low Voltage Controls 5-8 and Ground are used to control devicesthat work with an analog 0-10V signal. Ground provides the negativereference for the output voltages. All Grounds are connectedinternally to each other. Each output, 5-8, can sink or source 0-100mAat any voltage from 0-10VDC. The load level sets the percentagebetween the minimum and maximum voltage that is selected for thatload.NOTE: Loads 1 – 8, Low Voltage outputs, should be limited to250 feet / 76.2 meters for each wire run, using a minimum of18AWG / 0.823mm2 gauge wire. All LV connections use 4.4inch pound torque. Stranded wire recommended. |
Related manuals for Vantage Hearth LVOS-0-10-PWM-1
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved