Utilitech UTTND002 Programming Instructions Manual

Utilitech UTTND002 Programming Instructions Manual Manual pdf 1 page image

2. Programming CURRENT TIME (Time Setup)a. Press the “SET” button once to enter into Time Setupmode. The icon “SET TIME” will flash.b. Press the “SET” button again to select the “SET TIME”mode. With the initial setup, the “12” and “AM” willflash. NOTE: When changing the Current Timeprogramming after the initial setup, the “12” may bereplaced by a different hour number.c. Using the “-” and “+” buttons, advance the hour, payingspecial attention to the AM and PM.d. Press “SET” to save the hour and activate the minutes.The “00” will flash and either the “AM” or “PM” will besolid. NOTE: When changing the Current Timeprogramming after the initial setup, the “00” may bereplaced by different minute numbers.e. Using the “-” and “+” buttons, advance the minutes.f. Using the “DAY” button, select the current day ofthe week.g. Press the “ON/OFF” button to save settings or waitabout 10 seconds and the programmed time will beautomatically saved.3. Programming ON/OFF EVENTS (Event Setup)a. Press the “SET” button once to enter into TimeSetup mode. The icon “SET TIME” will flash.b. Press the “+” button to change to the Event Setupmode. The icon “SET PROGRAM” will flash. Thenumber “1” will appear in the lower left corner. Bycontinuing to press the “+” button, it will cycle throughall 8 potential programs. Stop on the program to beset up.c. Press the “SET” button to select the “SET PROGRAM”mode for the program number chosen (1 - 8). The hourand “AM” or “PM” will flash. With the initial setup thehour/colon will appear as “- :” on the LCD screen.NOTE: When changing the ON Event setting after theinitial setup, the dash representing the hour may bereplaced by an actual number.d. Using the “-” and “+” buttons, enter the hour of thedesired ON time, paying special attention to the AMand PM.e. Press the “SET” button to save the hour and activatethe minutes. The minutes represented by either a “--”or “00” and the “AM” or “PM” will be solid. NOTE:When changing the ON Event setting after the initialsetup, the dashes or “00” representing the minutesmay be replaced by numbers.f. Using the “-” and “+” buttons, enter the minutes of thedesired ON time.g. Using the “DAY” button, enter the desired day(s) ofweek for programming to be ON. Choose anyindividual day or blocks of days including MO-FR,SA-SU, or MO-SU.h. Press the “SET” button to save the ONprogramming. With the initial setup the hour/colonwill appear as “- :” on the LCD screen. NOTE: Whenchanging the OFF Event setting after the initialsetup, the dash representing the hour may bereplaced by an actual number.i. Using the “-” and “+” buttons, enter the hour of thedesired OFF time, paying special attention to the AMand PM.j. Press the “SET” button to save the hour andactivate the minutes. The minutes represented byeither a “--” or “00” and the “AM” or “PM” will besolid. NOTE: When changing the OFF Event settingafter the initial setup, the dashes or “00”representing the minutes may be replaced bynumbers.k. Using the “-” and “+” buttons, enter the minutes ofthe desired OFF time.l. Using the “DAY” button, enter the desired day(s) ofweek for programming to be OFF. Choose anyindividual day or blocks of days including MO-FR,SA-SU, or MO-SU.m. Press the “ON/OFF” button to save settings, or waitabout 10 seconds and the programmed Events willbe automatically saved.n. Repeat Step 3 to program up to 8 different ON/OFFEvents.4. REVIEWING, CHANGING and DELETING Eventsa. Press the “SET” button once to enter into TimeSetup mode. The icon “SET TIME” will flash.b. Press the “+” button to change to the Event Setupmode. The icon “SET PROGRAM” will flash. Thenumber “1” will appear in the lower left corner. Bycontinuing to press the “+” button, it will cyclethrough all 8 potential programs. Stop on theprogram desired.c. Press the “SET” button to select the “SETPROGRAM” mode for the program number chosen(1 - 8).d. TO REVIEW THE EVENTS, continue to press the“SET” button and it will cycle through the programchosen, one setting at a time.PROGRAMMING INSTRUCTIONSWAAV7-DAY TIMERITEM #0608803MODEL #UTTND002INITIAL SETUP1. Locate the tab at the topright of the sticker and pullto remove sticker from theface of the screen.2. Plug the timer into anyoutlet for 30 minutes tocharge the internal battery.3. Unplug and program timer.4. Plug programmed timerinto an electrical outlet.Timer will rest againstoutlet at a slight upwardangle, making it easier tosee and operate.5. Attach one device tothe timer. Plug the deviceinto the outlet on the sideof the timer.Call customer service at 1-866-994-4148,8 a.m. - 6 p.m., EST, Monday - Thursday,8 a.m. - 5 p.m., EST, Friday.AB141039SET DAYOnOff+-ResetRandomR12:00008 OFFONSETTIMESETPROGAM PMRMO TU WE TH FR SA SU1. Entering SETUP MODESNOTE: There are 2 different setup modes: TimeSetup, where the current time of day should beentered, and Event Setup, where up to 8 ON/OFFevents are programmed to control attached devices.The icons for these two events display as follows onthe timer LCD screen:SET PROG will have a number 1 through 8 after it,indicating the program being set up.a. Press the “SET” button once to enter into setupmode. The icon “SET TIME” will flash.b. Press the “-” or “+” buttons to move between“SET TIME” and “SET PROG 1 - 8”.c. When the desired mode is flashing, press “SET”to select.Mode LCD Screen IconTime Setup SET TIMEEvent Setup SET PROGRAM1 - 5SETResetRandomROnOff-+DAY12:00008 OFFAM PMRMO TU WE TH FR SA SUSETTIMESETPROGON2OnOffDAY+ R12:0000OFFAM PMRTU WE TH FR SA SUON1SET DAYOnOff+-ResetRandomR12:00008 OFFAM PMRMO TU WE TH FR SA SUSETTIMESETPROGON3OnOff+DAY:0000AM PMRWE TH FR SA SU5SETResetRandomROnOff-+DAY12:00008 OFFAM PMRMO TU WE TH FR SA SUSETTIMESETPROGON4

/ 4

Related manuals for Utilitech 0608803