Menu
Ultra electronics EOTec MXB-MM2 Installation Instructions Manual
  | |
Safety and Warning InformationImportant Notice - Before utilizing the product, the user shoulddetermine the suitability of the product for its intended use. Theuser assumes all risk and liability in connection with such use.ULTRA ELECTRONICS’ WRITTEN WARRANTY FOR THEPRODUCT IS MADE IN LIEU OF ALL OTHER WARRANTIES,EXPRESSED OR IMPLIED WARRANTIES OFMERCHANTABILITY AND FITNESS FOR A PARTICULARPURPOSE. The user's exclusive remedy for breach of UltraElectronics' written warranty shall be the repair or replacement ofsuch quantity of product which is proven to be defective. In nocase shall Ultra Electronics be liable for any special, incidental, orconsequential damages based upon breach of contract,negligence, strict liability or other legal theory.Approval Agency Controlled DocumentNo changes authorized without prior agency approvalPublication Number: RM0900202 Rev. 0Installation InstructionsOriginal InstructionsMX Multiplexer Base ModulesFor use ONLY with theEOTec MX Multiplexer LineUltra ElectronicsN UCLEAR SENSORS & PROCESS INSTRUMENATION707 Jeffery Way, PO Box 300Round Rock, TX 78680-300 USAToll Free: 800-880-9333Telephone: +1 512-434-2850Fax: +1 512-434-2901Email: fiberop@ultra-nspi.comwww.ultra-nspi.comUltra Electronics, Nuclear sensors & ProcessInstrumentation is a business name of Weed InstrumentCo., Inc .When operating, do not look directlyinto the transmit optical port or usemagnification or focusing equipment toview optical output.IEC 60825-1, Class 1 Laser ProductFDA 21 CFR 1040.10 & 1040.11CAUTION: Use of controls and/or adjustments or theperformance of procedures other than thosespecified herein may result in hazardous radiationexposure.Connect the DIN Rail, via the Model2A09 End Clamp, to Protective Earth(PE) ground with low impedance.ATEX Specific Conditions of UseModules shall be installed in an enclosure whichmaintains an ingress protection rating of IP54 and meetsthe enclosure requirements of EN60079-0 andEN60079-15. The EOTec modules shall be installed inDIN rail with DIN end clamps mounted on both sides ofthe module set. The DIN rail must be connected toProtective Earth in order to provide modules with aProtective Earth connection. Do not disconnectequipment connections or modules when energized.Nuclear Sensors &Process InstrumentationPower: At the top of the module, a pluggable screwterminal block is provided to apply power from a,nominal 24Vdc source. The MX Base Moduleprovides this received power to all additional I/Omodules connected via the 10+2 integrated BUSinterconnection.Alarm Relay: Also, at the screw terminal block arecontacts of a Form-C (SPST) Alarm Relay whichprovide a remote fault indicator. There are four faultsthat will engage the relay: An I/O module mismatch, aloss of power, a loss of the optical signal, or a loss ofthe optical signal at remote receiver will set this alarm(engage relay).SFP: MX Base modules use Small Form-factorPluggable (SFP) transceivers with LC connectors.This replaceable transceiver determines the transmitand receive specifications of the MX Base module.ConnectionsEOTec MX Multiplexer ModelsMXB-MM2 / MXB-SM15MXB-SM40 / MXB-SM80MX Base ModulesServiceService of this equipment is to be performed by UltraElectronics, NSPI only. This unit has no scheduledreplacement of parts. For installation manuals in acommunity language other than English please contactUltra Electronics, NSPI. |
Related manuals for Ultra electronics EOTec MXB-MM2
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved