Toshiba RAV-SM564UTP-E Installation Manual

Also see for RAV-SM1104UTP-E (TR): Service manual Service manual Installation manual Service manual

– 34 –4 InstallationREQUIREMENTStrictly comply with the following rules to prevent damage of the indoor units and human injury.• Do not put a heavy article on the indoor unit. (Even units are packaged)• Carry in the indoor unit as it is packaged if possible. If carrying in the indoor unit unpacked by necessity, be sure touse buffering cloth, etc. to not damage the unit.• To move the indoor unit, hold the hooking metals (4 positions) only.Do not apply force to the other parts (refrigerant pipe, drain pan, foamed parts, or resin parts, etc.).• Carry the package by two or more persons, and do not bundle it with plastic band at positions other than specified. External view (Unit: mm)(mm)Model RAV- A B C D Model RAV- A B C DSM56 Type 256 Ø6.4 Ø12.7 120 SM140 Type 319 Ø9.5 Ø15.9 183SM80 Type 256 Ø9.5 Ø15.9 120 SM160 Type 319 Ø9.5 Ø15.9 183SM110 Type 319 Ø9.5 Ø15.9 183Ceiling bottomsurface Knockout square holefor divide ductFor Ø150Knockout squarehole for divide ductFor Ø150840 Unit external dimensionCeiling bottom surfaceElectricalcontrol boxRefrigerant pipeconnecting port(Liquid) BRefrigerant pipeconnecting port(Gas) CTake-in portof wiresCeilingbottomsurfaceDrain pipeconnectingportKnockout square holefor divide ductFor Ø150Hanging bolt M10 or Ø3/8(Locally procured)Knockout square hole for divide ductFor Ø150690 ± 20 Hanging bolt pitch860 to 910 Ceiling opening dimension950 Panel external dimensionKnockout square hole for humidifierCeiling panel (sold separately)Ceiling bottom surfaceZ viewKnockout forsimple OAFor Ø100Ceiling bottomsurface860 to 910 Ceiling opening dimension780 Hanging bolt pitch950 Panel external dimension Opening a ceiling andinstallation of hanging bolts• Consider the piping / wiring before the unit is hungwhen determining the location of the indoor unitinstallation and orientation.• After the location of the indoor unit installation hasbeen determined, open the ceiling and installhanging bolts.• The dimensions of the ceiling opening and hangingbolt pitches are given in the outline drawing and theattached installation pattern.• When a ceiling already exists, lay the drain pipe,refrigerant pipe, indoor unit / outdoor unit connectionwires, and remote controller wires to their connectionlocations before hanging the indoor unit.Procure hanging bolts and nuts for installing the indoorunit (these are not supplied).◆ How to use the installation pattern(accessory)The installation pattern is provided inside thepackaging cap.Use the installation pattern positioning a ceilingopening and hanging bolts.Use the installation pattern to position the ceilingopening when hanging a ceiling.• After the hanging bolts have been installed, installthe indoor unit.• Hook the four holes in the installation pattern to thepanel fixing screws of the indoor unit.• When hanging a ceiling, open the ceiling along theoutside dimensions of the installation pattern.◆ Treatment of ceilingThe ceiling differs according to structure of building.For details, consult your constructor or interior finishcontractor.In the process after the ceiling board has beenremoved, it is important to reinforce ceiling foundation(frame) and to keep horizontal level of installed ceilingcorrectly in order to prevent vibration of ceiling board.1. Cut and remove the ceiling foundation.2. Reinforce the cut surface of ceiling foundation, andadd ceiling foundation for fixing the end of ceilingboard.◆ Installation of hanging boltUse M10 hanging bolts (4 pcs, locally procured).Matching to the existing structure, set pitch accordingto size in the unit external view as shown below.Hanging bolt M10 or W3/8 4 piecesNut M10 or W3/8 12 piecesIndoor unitPanel fixingscrewInstallation pattern (Accessory)HoleNew concrete slabInstall the bolts with insert brackets or anchor bolts.Steel flame structureUse existing angles or install new support angles.Existing concrete slabUse a hole-in anchors, hole-in plugs, or a hole-in bolts.RubberAnchor bolt(Blade typebracket)(Slide typebracket) (Pipe hanginganchor bolt)Hanging boltHanging bolt Support angle67-EN 68-EN+001114119401_01EN.book Page 34 Wednesday, October 31, 2012 4:56 PM

/ 56

Related manuals for Toshiba RAV-SM1104UTP-E (TR)

Toshiba RAV-SM404MUT-E Owner's Manual

Toshiba RBC-AX32U(W)-E Owner's Manual

This manual is suitable for:

RAV-SM1104UTP-E (TR)RAV-SM1404UTP-E (TR)RAV-SM1604UTP-E (TR)RAV-SM564UTP-E (TR)RAV-SM804UTP-E (TR)

Toshiba RAV-SM564UTP-E Installation Manual

Product

Learn More

Legal