Toshiba G9 ASD Quick Start Manual

Also see for ACE-tronics G9 ASD: Quick start guide Simple Start Guide Installation and operation manual Simple Start Guide

G9 ASDSimple Start GuideG9 ASD Simple Start GuideThe G9 ASD Simple Start Guide provides instructions on installation and operating procedures only.For additional information regarding your new G9 ASD, consult the G9 ASD Installation and Operation Manual.DO NOT attempt to install or operate the G9 ASD until you have read and understood all of the user directionscontained in this guide, and the product safety information and product labels contained in the G9 ASD Installationand Operation Manual. Equipment warning labels provide useful information and indicate an imminently hazardoussituation that may result in serious injury, severe property and equipment damage, or loss of life if safe procedures arenot followed. Installation and operation shall be performed by qualified personnel only.Frequently Asked QuestionsGeneralQ: I did not receive an I nstallation and Operation Manual with my ASD. How can I get one?A: T he G9 ASD Quick Start Guide and the G9 ASD I nstallation and Operation Manual can be downloaded from our website . T o request a hard-copy of either documentcontact the Toshiba Customer Support Center or your local Toshiba distributor.Q: Does Toshiba of fer training courses?A: Yes. Training courses are of fered at TIC headquarters in Houston, Texas. There are two types of training — maintenance and repair (nominal fee), and applications (free). Our instructors have yearsof hands-on experience in their respective fields and are continually being trained on new products. Students will gain valuable experience on the equipment and troubleshoot real faults thatmay be incurred during normal ASD setup, operation, and maintenance. For a listing of upcoming training courses or to register, visit our website and click on the training tab.Q: Where can I find additional information aboutT oshiba I nternational Corporation (T I C) and T I C products?A: Additional information can be found on our website. Y ou may also contact T I C for additional informationby writing to 13131 West L ittle Y ork R d., Houston, T exas, 77041, viatelephone at (713) 466-0277, or via fax at (713) 937-9349.Application SpecificQ: Who is considered qualified personnel?A: A qualified person is one who has the skills and knowledge about the construction, installation, operation, and maintenance of the equipment and has received safety training on the hazardsinvolved. Qualified personnel are able to recognize and properly address hazards associated with the application of motor-drive n equipment, and are trained to safely energize, de-energize andground said equipment, to safely lockout/tagout circuits and equipment, and clear faults in accordance with established safety practices.Q: What do I do if my motor is rotating in the wrong direction?A: Qualified personnel should reverse any two of the three ASD output power leads (U/T1, V/T2, or W/T3) connected to the motor.Q: For safety and application-specific reasons I need to remotely mount the ASD. How do I accomplish this?A: Select a mounting location that is easily accessible by the user and mark the location of the screw holes. After drilling the s crew holes, attach and secure the Electronic Operator Interface (EOI) tothe front side of the mounting location. Connect the extension cable. For information on required hardware or for instructions on remote mounting using a Remote Mounting Kit, consult the G9ASD Installation and Operation Manual. If further assistance is required, contact the Toshiba Customer Support Center.Q: I followed all of the instructions but my motor will not run. What now?A: Ensure that the input power to the ASD is connected and that the voltage at R/L1, S/L2, and T/L3 are as specified for your unit. Ensure that the terminals of the terminal board are configuredcorrectly for your application. Perform a Reset (to factory default settings). Ensure that the Local/Remote key is as required for your application and that you have provided a run command. Iffurther assistance is required, contact the Toshiba Customer Support Center.Q: During system operation I receive error messages that I do not understand. Where can I find information about trips/faults/alarms and troubleshooting?A: A complete list of LED and LCD screen displays, trip/fault/alarm descriptions and a list of possible causes of all trips/faults/alarms can be found in the G9 ASD Installation and Operation Manual.Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

/ 4

Related manuals for Toshiba ACE-tronics G9 ASD