Toshiba ASC400-T Operation Manual

TY-ASC400Toshiba Wireless Sound SystemOperation ManualThank you for purchasing this Portable Sound System.To use this product safely, read and understand this operation manual thoroughly before using.After reading this manual, keep it in a safe place so that it can be referred to when necessary.5016800Safety precautionsThe information you need to prevent danger to the user and other people as well as property damage is describedbelow. “Description of signs” shows different levels of danger or damage that may occur due to wrong handling.Important notes•This book is only a guide for user's operation, not a criterion for configuration.•Only use attachments/accessories specified by the manufacturer.The lightning flash is intended to alert the user to the presence of dangerous voltage within theproduct's enclosure, and touching the internal components may result in a risk of electric shock topersons.The exclamatory mark is intended to alert the user to the presence of important operatinginstructions.To reduce the risk of electric shock or fire, do not open the cover. Refer servicing to qualified servicepersonnel.Description of signsIndicates that there is a risk of death orserious injury.Indicates that there is a risk of minorinjury or property damage.What to do in the case of an abnormality•Stop using the device immediately in the case of an abnormality or failure.•Remove the power plug from the receptacle immediately when water or any foreign objectenters the interior of the device.It may cause a fire or electric shock. Remove the power plug immediately, and contact your dealerfor a repair.Power cord and power plugTo reduce the risk of fire, electric shock or product damage,•Insert the power plug fully into an AC receptacle.•If you find dust on the power plug pin or pin installation surface, remove the power plug andremove the dust.•The mains plug or an appliance coupler is used as a disconnecting device, the disconnectingdevice shall remain readily operable.•Do not insert or remove the power plug with a wet hand.•Observe the following when handling the power cord.•Do not damage it. • Do not modify it (e.g. extension). • Do not heat it.•Do not pull it. • Do not place a heavy object on it. • Do not pinch it.•Do not bend it forcefully. • Do not twist it. • Do not bundle it.•If the device will not be used for a long time, remove the power plug from the receptacle.•Do not use any power cord other than the one that comes with the device.•Do not use the power cord that comes with the device for any other product.UsageTo reduce the risk of fire, electric shock or product damage,•Do not disassemble, repair, or modify the device.•Do not insert any foreign object into the device.•In case of lightning, do not touch the power cord.•Before carrying the device, remove the power plug from the receptacle.•Do not place a heavy object on the device.•To prevent possible hearing damage, do not listen at high volume levels for long periods.InstallationTo reduce the risk of fire, electric shock or product damage,•Place the unit on a flat surface away from sources of direct sunlight or excessive heat.•Do not install the device in a confined or build-in space such as a book case or similar area, andkeep it under a well-ventilated condition. The ventilation should not be impeded by coveringthe ventilation openings with items such as newspaper, table-cloths, curtains, etc.•Do not expose the device to rain, moisture, dripping, or splashing.•Do not place objects filled with liquids, such as vases, on the device.Note•If any color shift occurs on a nearby TV or the radio of the device picks up noise from the TV, keep the device awayfrom the TV.Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with onewider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or thethird prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician forreplacement of the obsolete outlet.10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and thepoint where they exit from the apparatus.11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with theapparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoidinjury from tip-over.13. Unplug this apparatus during lightning storms or when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in anyway, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.15. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that itdoes not require a safety connection to electrical earth.16. No naked flame sources, such as lighted candles, should be placed on the apparatus.17. Attention should be drawn to environmental aspects of battery disposal.18. The product is designed to use in moderate climates.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Thisequipment should be installed and operated with minimum distance 20CM between the radiator & your body.FCC Statement :This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference, and 2) This device must accept any interference received,including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuantto part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference toradio communication. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help.Caution: Changes or modifications not expressly approved by the party responsible for compliance could voidthe user’s authority to operate the equipment.IC-CANADA :This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the followingtwo conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device.This Class [B] digital apparatus complies with Canadian ICES-003.Cet appareil s’accorde avec Industrie Canada licence-exempte RSS standard. (1) cet appareil ne peut pas causerl’intervention, et (2) cet appareil doit accepter de l’intervention, y compris l’intervention qui peut causerl’operation non desiree de.Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.California Prop 65 Warning :This product contains chemicals, including lead, known to the State of California to causecancer and birth defects or other reproductive harm. Wash hands after handling.Disclaimer•Toshiba shall not be responsible for any damage caused by an earthquake, thunderstorm, flood damage, firefor which Toshiba is not responsible, acts of a third party, other accidents, or damages caused by the user'swillful acts or negligence, misuse, or use in abnormal conditions.•Toshiba shall not be responsible for any damage caused by failure to observe the information described in theoperation manual.Disposal•When disposing of the device, observe the laws, or ordinances and rules of the local government.About using Bluetooth®This unit is designed for use with Bluetooth® wireless devices compatible with the A2DP and AVRCP streaming audioprofiles. Refer to your Bluetooth® device’s user manual or technical support to determine if your Bluetooth® devicesupports these profiles.Frequency band usedThis unit uses the 2.4 GHz frequency band. However other wireless devices may use 2.4 GHz frequency band as welland may cause interference with each other. To avoid interference, please refrain from the use of the unit at the sametime with other wireless devices.Certification of this deviceThis unit conforms to frequency restrictions and has received certification based on frequency laws, so a wirelesspermit is not necessary.However, the following action is punishable by law in some countries:•Taking apart/modifying the unit.Usage restrictions•Wireless transmission and/or use with all Bluetooth® equipped devices is not guaranteed.•A device featuring the Bluetooth® function is required to conform to the Bluetooth® standard specified by BluetoothSIG, and be authenticated. Even if the connected device conforms to the above mentioned Bluetooth® standard, somedevices may not be connected or work correctly, depending on the features or specifications of the device.Range of useUse this device within an unobstructed 10 m range. The range of use or perimeter may be shortened depending on anyobstructions, devices causing interference, other people in the room, or the construction of the building. Please notethat the range mentioned above is not guaranteed.The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and are used under license.Part names432122233124282930 27 26 2556891011713 15 17 19 201612 14 18 211 LINE OUT jack L/R2 LINE IN jack L/R3 FM ANTENNA4 AC POWER SOCKET5 3.5mm AUX INPUT jack6 6.3 mm MIC.2 jack7 USB port A8 6.3 mm MIC.1 jack9 DIMMER/LIGHT knob10 FUNC button11 MUTE button12 /PAIR/AUTO button13 ECHO button14 (TUN/10/FOLDER) button15 (DOWN/-PRESET) button16 DISPLAY17 (UP/+PRESET) button18 (TUN/10/FOLDER) button19 VOL. knob20 POWER button21 MIC. VOL. knob22 SD card slot23 USB port B24 SAMBA mode button25 JAZZ mode button26 ROCK mode button27 DISCO mode button28 POP mode button29 EQ button30 EQUALIZER Slide Volume31 Extra Bass buttonBasic functionsTurning the unit on/off1 Press the POWER button to switch the unit on/off.Setting the function mode1 To change the function mode, press the FUNC button on the unit to choose the USB A/USB B/SD/AUX/Bluetooth®/LINE/FM function.Note•In USB A/USB B/SD/AUX/Bluetooth®/LINE mode, when no operation is performed for 30 minutes, the unit willautomatically enter standby mode. To resume operation, press POWER button to switch the unit on again.Adjusting the volume1 Rotate the VOL. knob on the unit to increase or decrease the music volume.Muting the Volume1 Press MUTE button to switch the sound off temporary.2 To switch the sound on, press the MUTE button again.Light function1 Press the DIMMER/LIGHT knob repeatedly to switch the different lighting mode (L1~L4 and OFF) ofLED indicator light on the speaker.L1: Turning the light on. Hold down the LIGHT knob on the unit to choose BLUE/YELLOW/CYAN/PINK/WHITE/RED/GREEN color.L2: Blinking the light slowly. The color changes to BLUE/YELLOW/CYAN/PINK/WHITE/RED/GREEN automatically.L3: Blinking the light a little faster. The color changes to BLUE/YELLOW/CYAN/PINK/WHITE/RED/GREEN automatically.L4: Flashing the light.2 Rotate the DIMMER/LIGHT knob on the unit to adjust brightness of the display screen.Equalizer function1 Press the EQ button to enter to equalizer manual mode.2 Adjust the EQUALIZER Slide Volume for five frequencies (63Hz, 250Hz, 1kHz, 4kHz, 12kHz) on theunit to adjust the equalizer volume.3 To select the preset equaliser modes, press the POP/DISCO/ROCK/JAZZ/SAMBA button.Extra Bass1 Press Extra bass button to switch the extra bass on/off.Microphone echo1 Press ECHO button repeatedly to switch to microphone ECHO ON/OFF mode.USB/SD operationListening to a USB device/SD cardThis unit provides a USB port for music playback.1 Press the FUNC button on the unit to select USB A/USB B/SD mode.2 USB: Connect a USB memory stick to the USB port A/USB port B on the front of the unit.SD: Insert an SD memory card into the SD card slot on the front of the unit.The display will show the total number of playable tracks on the USB device/SD card.3 To playback and resume playback, press the /PAIR button.The current track number and the " " will be shown on the display.4 To pause playback, press the /PAIR button on the unit.The current track number and the " " will be shown on the display.5 To select a desired track, press the or button either while playing or while paused until thedesired track appears on the display.The unit will start playing automatically.6 To search for a particular passage during playback, press and hold the or button to fastforward and fast backward until the desired point (passage) is reached, then release the buttonfor normal playback.Playback will start again from this point.7 To jump to +/- 10 track, press or (TUN/10/FOLDER) button.8 To select +/- folder, press and hold or (TUN/10/FOLDER) button.Caution•To prevent harmful interference, always connect USB devices/SD card directly to the unit. Do not use a USB/SD cardextension cable to connect USB devices/SD card to the unit.Bluetooth® operation1 Press the FUNC button on the unit to switch to the Bluetooth® mode.The display will show "NO BT".2 Following the instructions in your device's user manual, activate Bluetooth® on your device andsearch for the unit "TY-ASC400" and connect. Input the password "0000" if required.The display will show "BT".3 Press the /PAIR button on the unit to start playback.4 Rotate the VOL. knob on the unit or adjust the volume on the external device to increase ordecrease the music volume as desired.Notes•Press and hold the /PAIR button to disconnect the Bluetooth®.•The Bluetooth® works best within 10 meters.•In bluetooth mode," /PAIR", "VOLUME", "MUTE" etc. are also active.AUX IN/LINE operation1 Press the FUNC button on the unit to select "AUX"/"LINE" mode.2 Connect your audio device to the input terminal AUX LINE INPUT on the front panel/on the rearpanel of the unit with an audio cable.3 Rotate the VOLUME knob on the unit or adjust the volume on the external device to increase ordecrease the music volume as desired.4 Control playback with your audio device.170417c1_TY-ASC400_EN.indd 1 2017/04/17 10:42:42

/ 4

Related manuals for Toshiba ASC400-T