Form No. 3466-395 Rev AGroundsmaster® 3300, 3310, and3200 2-Wheel or 4-Wheel DriveTraction UnitModel No. 31900A—Serial No. 400000000 and UpModel No. 31901A—Serial No. 400000000 and UpModel No. 31907A—Serial No. 400000000 and UpModel No. 31909A—Serial No. 400000000 and UpRegister at www.Toro.com.Original Instructions (EN) *3466-395*

Toro 31900A Operator's Manual

3200

Introduction

Toro Riding Mower Safety

maintenance and storage

Sound Pressure Level

Specifications

Setup

Install Wheels

Install Seat

Check Angle Indicator

Install ROPS

Mount Carrier Frames To Cutting Units

Mount Cutting Units

Mount Cutting Unit Drive Motors

Before Operating

Check Cooling System

Check Tire Pressure

Check Reel To Bedknife Contact

hour meter

Operation

Bleeding Fuel System

Operating Characteristics

Mowing Techniques

Selecting Clip Rate (Reel Speed)

Standard Control Module (SCM)

Lubrication

Maintenance

Daily Maintenance Checklist

Service Interval Chart

General Air Cleaner Maintenance

Fuel System

Bleeding Air From Injectors

Servicing Engine Belts

Changing Hydraulic Fluid

Adjusting Traction Drive For Neutral

Battery Care

Electrical Schematic

Hydraulic Schematic

Storage

The Toro General Commercial Products Warranty

Foreword

Safety Instructions

while operating

Safety and Instruction Decals

Set-Up Instructions

Install Rear Fenders

Install Front Fenders

Full Bed Removal (Model 07212 only)

Re-install the Full Bed (Model 07212 only)

Fill the Fuel Tank

Check the Cooling System

Check Front Differential Oil

Check Brake Fluid

Controls

Operating Instructions

Stopping the Vehicle

Passengers

Hills

Loading and Dumping

Four-Wheel Drive

Trailer Towing

Quick Coupler Operation

Quick Reference Chart

Using Bed Safety Support

Jacking the Vehicle

General Air Cleaner Maintenance Practices

Changing Engine Oil and Filter

Changing Engine Coolant

Adjusting Belts

Changing Transaxle/Hydraulic Fluid

Cleaning Hydraulic Strainer

Adjusting the Brake Pedal

Adjusting Parking Brake

Adjusting the High-Low Cable

Inspect Constant Velocity Boot

Battery Storage

Maintenance Schedule

Hydraulic Schematic (Base Vehicle)

Hydraulic Schematic (Vehicle w/Remote Hydraulic Kit) (MODEL 07211 TC Only)

Electrical Schematic (Base Vehicle)

Electrical Schematic (Vehicle w/Remote Hydraulic Kit) (MODEL 07211 TC Only)

Identification And Ordering

Safety

While Operating

Install the Wheels

Install the Steering Wheel

Install the ROPS

Full Bed Removal

Product Overview

gear shift lever

light switch

Attachments/Accessories

Fill Fuel Tank

Check Fan Belt Tension

Driving Vehicle

Tipovers

Loading And Dumping

Four Wheel Drive

Hydraulic Control

Premaintenance Procedures

Jacking Vehicle

Engine Maintenance

Replacing Spark Plugs

Fuel System Maintenance

Jump Starting Vehicle

Drive System Maintenance

Inspect Tires

Cooling System Maintenance

Brake Maintenance

Controls System Maintenance

Adjusting Brake Pedal

Hydraulic System Maintenance

Schematics

check tire pressure

Operating

stopping the vehicle

transporting the vehicle

maintenance schedule

jacking the vehicle

jump starting procedure

Supervisor's Responsibilities

Dimensions

Re–Install Full Bed

Check Transaxle / Hydraulic Fluid

Check Torque Of Wheel Nuts

parking brake

Pre–starting Checks

Stopping Vehicle

Speed

Using The Differential Lock

Heavy Duty Operation

Changing Engine Oil And Filter

Removing Debris From Engine Cooling System

Adjusting Accelerator Pedal

Replacing Hydraulic Filter

battery storage

31900A

31901A

31907A

31909A

Groundsmaster 3300

Groundsmaster 3310 Series

Toro 31900A Operator's Manual

Product

Learn More

Legal