OneStart

Menu
Toro 30604 Operator's Manual Manual pdf 42 page image

Toro 30604 Operator's Manual

Also see for 30604: Operator's manualOperator's manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Safety
  4. Safety and Instructional Decals
  5. Setup
  6. Checking the Tire Pressure
  7. pto switch
  8. adjusting the seat
  9. Specifications
  10. Checking the Engine-Oil Level
  12. Checking the Torque of the Wheel-Lug Nuts
  13. Adjusting the Height of Cut
  14. Adjusting the Skids
  15. Adjusting the Blade
  16. Checking the Safety-Interlock Switches
  17. Starting and Stopping the Engine
  18. Reversing Fan Operation
  19. Operating Tips
  20. After Operation
  21. Hauling the Machine
  22. Maintenance
  23. Daily Maintenance Checklist
  24. Service Interval Chart
  25. Preparing the Machine for Maintenance
  26. Engine Maintenance
  28. Changing the Engine Oil and Filter
  29. Fuel System Maintenance
  30. Electrical System Maintenance
  31. Locating the Fuses
  32. Drive System Maintenance
  33. Checking the Rear-Axle Lubricant
  34. Checking the Rear Wheel Toe-In
  35. Servicing the Engine-Cooling System
  36. Belt Maintenance
  37. Replacing the Blade-Drive Belt
  38. Hydraulic System Maintenance
  39. Changing the Hydraulic Fluid
  40. Replacing the Hydraulic Filters
  41. Mower Maintenance
  42. Adjusting the Mower-Deck Pitch
  43. Servicing the Caster Wheels and Bearings
  44. Replacing the Mower-Deck-Hinge Covers
  45. Removing and Installing the Mower Blade(s)
  46. Correcting a Mower-Deck Mismatch
  47. Storage
Toro 30604 Operator's Manual Manual pdf 42 page image
Figure 48Note: When using different oil, drain all old oil fromthe crankcase before adding new oil.Changing the Engine Oil andFilterService Interval: Every 250 hours1. Start the engine and let it run 5 minutes to allow theoil to warm up.2. Park the machine on a level surface, shut off the engine,remove the key, and wait for all moving parts to stopbefore leaving the operating position.3. Replace the engine oil and filter (Figure 49).Figure 494. Add oil to the crankcase; refer to Checking theEngine-Oil Level (page 41).42
/ 64
Related manuals for Toro 30604
Toro 30606 Operator's Manual first page preview
Toro 30606 Operator's Manual
Toro 30605 Operator's Manual first page preview
Toro 30605 Operator's Manual
Toro 30607 Operator's Manual first page preview
Toro 30607 Operator's Manual
Toro 30602 Operator's Manual first page preview
Toro 30602 Operator's Manual
Toro 30609 Operator's Manual first page preview
Toro 30609 Operator's Manual
Toro 30607A Operator's Manual first page preview
Toro 30607A Operator's Manual
Toro 30605TE Operator's Manual first page preview
Toro 30605TE Operator's Manual
Toro 30645 Operator's Manual first page preview
Toro 30645 Operator's Manual
Toro 30695 Operator's Manual first page preview
Toro 30695 Operator's Manual
Toro 30672 Operator's Manual first page preview
Toro 30672 Operator's Manual
This manual is suitable for:
306043060530608Groundsmaster 4000Groundsmaster 4100
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved