Team Losi Mini 8IGHT Instruction Manual

Also see for 8IGHT: Instruction manual Owner's manual Instruction manual Owner's manual Instruction manual

Contents

Team Losi Mini 8IGHT Instruction Manual Manual pdf 5 page image

ENsPEEd contRoL PRogRaMMingWhen the ESc is turned on, it will check the connection between the Redand White wire. If the wires are shorted, it will go into brushed motor mode.Brushed Motor• Motor (+) connected to Red and White Wire of ESc• Motor (-) connected to Black Wire of EScBrushless Motorconnect the 3 motor wires to the Red, White and Black wires of the ESc.If the motor runs in the reverse direction after calibration, disconnect any2 motor wires from the ESc and reconnect those 2 motor wires in theopposite orientation.BATTERy TyPE PRoGRAmmING1. LED indicatorOnce the power is turned on, the LED will display the selected Battery Typefor 2 seconds.Red and Green LEDs are used to display the selected Battery Type:• Red LED Flashing = LiPo is selected• Green LED Flashing = NiMH/Nicd is selectedTo change from one battery type to another, press the setup buttonduring the first 2 seconds after turning on the ESc. The cutoff voltage willautomatically adjust based on battery type.• For LiPo battery: The ESc will auto detect whether it is 2-cell, 7.4V (6.0Vcutoff) or 3-cell, 11.1V (9.0V cutoff)• For NiMH: The ESc will cut off at 4.3V2. LED display during “Normal Operation”3. One-Touch Endpoints Calibration Programming:a. Turn on the Transmitter with throttle in neutral position.b. Hold the ESc setup button and turn on ESc.c. The Red and Green LED will turn on; release setup button.d. The Green LED will begin flashing; pull trigger to full throttle positionuntil Green LED turns solid, then return to neutral position.e. The Red LED will begin flashing; push trigger to full brake/reverseposition until Red LED turns solid.f. Release trigger to neutral position and programming is complete.4. LED display for “Error”a. Battery Voltage is too high (over 13V)—Solid Red LED and Green LEDflashing slowly (Only during Power ON)b. Overheat—Alternatively Flashing Red and Greenc. Motor Failure (Bad Motor, Locked Rotor, Bad connection)—Red LEDflashing quickly 3 times (repeating sequence)d. Battery Low—Solid Green LED and Red LED flashing slowly5. ESC Profile Selection:a. When the ESc is at the neutral position, the Green LED can be used toindicate the currently selected profile:b. To select ESc profile:• With ESc at neutral position, hold the setup button over 5 secondsto change the ESc profileRecalibrating and adjusting the Msc-18BL hP EscTransmitter and Receiver BindingBinding Procedure1. Make sure the transmitter and vehicle are both powered off.2. Install a bind plug in the receiver battery/bind port. You do not need to remove any of the other plugs to re-bind.3. With the Bind plug installed, turn on the vehicle. Notice a blinking Orange LED within the receiver.4. Power on the transmitter. The orange LED on the rear of the transmitter will blink.5. When the receiver binds to the transmitter, the receiver light will turn solid.6. Power off the transmitter and vehicle.7. Disconnect the battery from the ESc. Remove the bind plug from the receiver.8. Safely store the bind plug.9. The receiver will keep the binding to the transmitter until another binding is done.condition LEdStop GreenPartial Forward OffMax Forward RedPartial Reverse OffMax Reverse RedBrake Red and GreenProfile green LEdForward/Reverse Mode Solid ONForward Only Slow Flashingtechnical specificationsnoticE: Only power this vehicle with the stock 6-cell, 7.2-Volt NiMHbattery pack (LOSB1209), a 2-cell, 7.4-Volt LiPo battery pack (LOSB9835)or 3-cell, 11.1-Volt LiPo battery pack (LOSB9836). The use of highervoltage battery packs will cause ESc damage and void any warranty.sensorless Brushless EscResistance per phrase 0.0017 Ohmcurrent 32A continuous current,260A burst currentMax RPM 80,000Battery compatibility 4- to 7-cell NiMH/Nicd, or 2- to 3-cell LiPoBEc 5V, 1AFunctionA On/Off SwitchB Setup ButtonBA5Losi Mini 8ight BRUshLEss BUggy• instRUction ManUaL