Sony XBA-2VP Operating Instructions Manual

Also see for XBA-2VP: Operating instructions

Contents

specifications

EnglishStereo headsetWARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rainor moisture.To reduce the risk of electrical shock, do not open the cabinet. Refer servicing toqualified personnel only.You are cautioned that any changes or modifications not expressly approved in thismanual could void your authority to operate this equipment.Features Earbuds with remote controller for smartphoneEasy-to-use remote control (for smartphone). Handsfree headset with microphone Newly developed Dual Balanced Armature driver unitNewly developed micro-size driver unit (full-range + woofer) reproduces smooth andclear vocal, with rich and powerful bass. Newly developed Double Layered HousingMagnesium inner housing holds the driver units rigidly for smooth sound response.Special ABS plastic outer housing prevents unwanted vibration for clear mid-highrange. Noise-blocking designNoise-blocking design attenuates ambient noise and sound leakage. Super-small bodyBalanced Armature driver unit allows for a super small body, and ultimate wearingcomfort.How to useUsing the supplied cord adjuster (see fig. -)You can adjust the cord length by winding the cord on the cord adjuster.(The cord can be wound to the cord adjuster up to 50 cm. If you wind more, the cordcomes off from the cord adjuster easily.)1 Wind the cord.2 Push cord into slot hole to secure in place.NoteDo not wind the plug or split section of the cord, as it will strain the cord and may cause a wire break.Using the remote and microphone with a smartphone(See fig. -)You can use this unit with smartphones.Notes If the microphone of the unit does not function, or you feel the volume level is not enough, connectthe unit to your smartphone via the supplied conversion cord. This unit is not guaranteed to operate digital music players.Parts and controls Microphone Volume control*1Rotate upward to increase the volume and rotate downward to decrease the volume.*1 There is a tactile dot beside MAX of the volume control. Answer/End button*2Press once to answer the call. Press again to end.*2 The button function may vary depending on the smartphone.Available operations for iPhonePlays/pauses a track of the connected iPhone product with a single press. Skips to thenext track with a double press. Skips to the previous track with a triple press. Starts the“VoiceOver*3” feature with a long press (if available).Hold down for about two seconds to reject an incoming call. When you let go, two lowbeeps confirm the call was rejected.*3 Availability of the “VoiceOver” feature depends on iPhone and its software version.Wearing the headphones (see fig. )1 Determine right and left headphone and hold them as in the illustration.There is a tactile dot on the unit marked  to distinguish the left side.2 Fit the headphones into your ears snugly, as in the illustration.3 Adjust the headphone to fit snugly in your ear.Installing the earbuds correctly (see fig. )If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoybetter sound quality, change the earbuds to another size or type, or adjust the earbudsposition to sit on your ears comfortably and fit your ears snugly. If the earbuds do not fityour ears, try another size or type. Confirm the size of the earbuds by checking the colorinside (see fig. - for hybrid silicone rubber earbuds and - for noise isolationearbuds).When you change the earbuds, install them firmly on the headphones to prevent theearbud from detaching and remaining in your ear.About hybrid silicone rubber earbuds (see fig. -)Earbud sizes (inside color)Small LargeSS(Red)S(Orange)M(Green)L(Light blue)To clean the hybrid silicone rubber earbudsRemove the earbuds from the headphones, and wash them with a mild detergentsolution.About noise isolation earbuds (see fig. -)Supplied noise isolation earbuds provides a snug fit for effective attenuation of ambientnoise.Earbud sizes (inside color)Small LargeS(Orange)M(Green)L(Light blue)Notes Prolonged use of the noise isolation earbuds may strain your ears due to their snug fit. If you haveexperience discomfort or pain in your ears, discontinue use. The pressure-relieving urethane cushion is extremely soft. Therefore, do not pinch or pull theurethane cushion. If the urethane cushion is broken or detached from the earbuds, it will not take itscorrect position and the earbuds will lose their noise isolation function. The pressure-relieving urethane cushion may deteriorate due to long-term storage or use. If thepressure-relieving power is lost and the urethane cushion becomes hard, the earbuds may lose theirnoise isolation function. Do not wash the noise isolation earbuds. Keep them dry, and avoid accumulation of water in thepressure-relieving urethane-cushions. Not doing so may cause early deterioration.To detach an earbud (see fig. -)While holding the headphone, twist the parts inside of the earbud and pull the earbudoff. TipIf the earbud slips and cannot be detached, wrap it in a dry soft cloth.To attach an earbud (see fig. -)Push the parts inside of the earbud into the headphone until the projecting part of theheadphone is fully covered.How to attach the clip to the cord (see fig. )1 Hold the clip closed, and pull up the lever on the clip just a little.2 Put the cord into the groove under the lever.Notes If you pull up the lever on the clip without holding the clip closed, or holding the clip closed butopening the lever too much, you cannot put the cord into the groove under the lever. Do not catch the cord on the projection of the clip or do not wedge it into the groove. It may damagethe wires of the cord. Do not move the clip position with the cord attached. It may damage the wires of the cord.Removing the headphonesAfter use, remove the headphones slowly.NoteHeadphones are designed to fit closely in your ears. If the headphones are pressed hard while in use ortaken off too quickly, they may cause injury.Wearing headphones may produce a diaphragm click sound. This is not a malfunction.1 2 Conversion cord1EarbudTactile dot23 Sectional View Colored partsPressure-relievingurethane cushion XBA-2VPStereo HeadsetOperating InstructionsManual de instrucciones4-418-201-31(1)©2011 Sony CorporationPrinted in ThailandSpecificationsHeadphonesType: Closed, Dual Balanced ArmatureDriver unit: Dual Balanced ArmaturePower handling capacity: 100 mW (IEC*1)Impedance: 8 Ω at 1 kHzSensitivity: 108 dB*2Frequency response: 4 Hz – 25,000 HzCord: 1.2 m (47 1/4 in) (Y-type)Plug: Four-conductor gold-plated stereo mini plugMass: Approx. 6 g (0.21 oz) (without cord)MicrophoneDesign: In-line microphoneType: Electret condenserOpen circuit voltage level: –38 dB (0 dB = 1 V/Pa)Effective frequency range: 20 Hz – 20,000 HzSupplied accessoriesHybrid silicone rubber earbuds: SS (red) (2), S (orange) (2), M (green) (attached to theunit at the factory) (2), L (light blue) (2)Noise isolation earbuds: S (orange) (2), M (green) (2), L (light blue) (2)Cord adjuster (winds cord up to 50 cm (19 3/4 in)) (1)Clip (1)Conversion cord (1)Carrying case (1)Card warranty (1)Operating Instructions (1)* 1 IEC = International Electrotechnical Commission* 2 150 mV inputDesign and specifications are subject to change without notice.iPhone® is a trademark of Apple Inc.Precautions Please keep your headphones clean at all times especially inside the rubber earbud.(see fig. )If any dust or ear wax is inside the earbud, you may experience some listeningdifficulties. Listening with headphones at high volume may affect your hearing. For traffic safety,do not use while driving or cycling. Handle the driver units carefully. Do not put weight or pressure on the headphones as it may cause the headphones todeform during long storage. The earbuds may deteriorate due to long-term storage or use. Install the earbuds firmly onto the headphones. If an earbud accidentally detaches andis left in your ear, it may cause injury. Store the earbuds where children cannot reach in order to prevent from accidentalingestion or choking. Do not leave the stereo headphones in a location subject to direct sunlight, heat ormoisture.Note on static electricityIn particularly dry air conditions, mild tingling may be felt on your ears. This is a resultof static electricity accumulated in the body, and not a malfunction of the headphones.The effect can be minimized by wearing clothes made from natural materials.Optional replacement earbuds can be ordered from your nearest authorized Sonyretailer or www.sony.com.

/ 2

Related manuals for Sony XBA-2VP