Sony XAV-601BT Installation/connections Manual

Also see for XAV-601BT: Specifications Operating instructions Installation/connections Operating instructions Operating instructions

4-419-668-52(1)Installation/ConnectionsAV CenterXAV-601BTAUX1 INAUX2 AUDIOINREVERSE INZxZ L / R*6SUB OUTAUX1 AUDIOINFRONTAUDIO OUTREARAUDIO OUTMIC IN*3REMOTE IN*7AUX2 INCAMERAREAR OUTEXTAUX IN( VIDEO )AUX AUDIOINCAMERAAUX1 IN( VIDEO )Connection exampleNotes (-A) Be sure to connect the ground (earth) lead before connecting the amplifier. The alarm will only sound if the built-in amplifier is used.Notes (-B) You cannot use multiple auxiliary devices simultaneously, even if theyare connected to different terminals. To connect an iPod via RC-202IPV, make sure to connect the videooutput plug to AUX1 IN.Connection diagram To a common ground (earth) pointFirst connect the black ground (earth) lead, then connect the yellowand red power supply leads. To the power antenna (aerial) control lead or thepower supply lead of the antenna (aerial) boosterNotes It is not necessary to connect this lead if there is no power antenna(aerial) or antenna (aerial) booster, or with a manually-operatedtelescopic antenna (aerial). If your car has a built-in FM/AM antenna (aerial) in the rear/sideglass, see “Notes on the control and power supply leads.”To AMP REMOTE IN of an optional poweramplifierThis connection is only for amplifiers. Connecting any other systemmay damage the unit. To a car’s illumination signalBe sure to first connect the black ground (earth) lead to a commonground (earth) point. To the +12 V power terminal which is energizedwhen the ignition switch is set to the accessorypositionNotes If there is no accessory position, connect to the +12 V power(battery) terminal which is energized at all times.Be sure to first connect the black ground (earth) lead to a commonground (earth) point. If your car has a built-in FM/AM antenna (aerial) in the rear/sideglass, see “Notes on the control and power supply leads.” To the +12 V power terminal which is energizedat all timesBe sure to first connect the black ground (earth) lead to a commonground (earth) point. To the parking brake switch cord To an auxiliary device such as a portable mediaplayer, game console, etc. (not supplied)TipYou can use an RCA cord (not supplied) to connect auxiliary devices. To the +12 V power terminal of the car’s rear lamplead (only when connecting the rear view camera)Notes on the control and power supply leads REM OUT lead (blue/white striped) supplies +12 V DC when you turn onthe tuner. If your car has built-in FM/AM antenna (aerial) in the rear/side glass,connect REM OUT lead (blue/white striped) or the accessory powersupply lead (red) to the power terminal of the existing antenna (aerial)booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with thisunit.Memory hold connectionWhen the yellow power supply lead is connected, power will always besupplied to the memory circuit even when the ignition switch is turned off.*1 Speaker impedance: 4 – 8 ohms × 4* 2 For details on installing the microphone, see “Installing the microphone()” on the reverse side.* 3 Whether in use or not, route the microphone input cord such that it doesnot interfere with driving. Secure the cord with a clamp, etc., if it isinstalled around your feet.* 4 RCA pin cord (not supplied)* 5 For details on connecting to the parking brake switch cord, see“Connecting the parking brake lead ()” on the reverse side.* 6 The sound is output from this terminal only when ZONE x ZONE isactivated. This terminal outputs a fixed level regardless of the volumecontrol of the unit.* 7 A separate adaptor may be required.* 8 Not supplied.Cautions Run all ground (earth) leads to a common ground(earth) point. This unit is designed for negative ground (earth) 12 VDC operation only. Do not disassemble or modify the unit. Do not install in locations which interfere with airbagoperation. Do not get the leads under a screw, or caught in movingparts (e.g. seat railing). Before making connections, turn the car ignition off toavoid short circuits. Connect the yellow and red power supply leads onlyafter all other leads have been connected. Be sure to insulate any loose unconnected leads withelectrical tape for safety. Do not press on the LCD when installing the unit. Install the unit with the monitor facing straight forward;do not install it at a slanted angle.Notes on the power supply lead (yellow) When connecting this unit in combination with otherstereo components, the amperage rating of the carcircuit to which the unit is connected must be higherthan the sum of each component's fuse amperage rating. If no car circuits are rated high enough, connect the unitdirectly to the battery.Parts list The numbers in the list correspond to those in theinstructions. The bracket  is attached to the unit before shipping.Before mounting the unit, use the release keys  toremove the bracket  from the unit. For details, see“Removing the bracket ()” on the reverse side of thesheet. Keep the release keys  for future use as they arealso necessary if you remove the unit from yourcar. Assemble the parts of the microphone  before use. Fordetails, see “Installing the microphone ()” on thereverse side.CautionHandle the bracket  carefully to avoid injuring yourfingers. CatchNoteBefore installing, make sure that the catches on both sides of the bracket are bent inwards 3.5 mm (5/32 in). If the catches are straight or bentoutwards, the unit will not be installed securely and may spring out.Equipment used in illustrations (not supplied)× 8× 2cbaFrom car antenna (aerial)REM OUTMax. supply current: 0.4 AFuse (10 A)Blue/white striped RedYellowWhiteGreenPurpleWhite/black stripedGray/black stripedGreen/black stripedGrayLeftRightLeftRightBlackPurple/black striped*5*8Light green PARKING BRAKEILLUMINATIONOrange/white striped*4*4*4*4*4FRONT AUDIOOUTSUB OUTREAR OUTZ×Z L / RREAR AUDIOOUTABVideo camera*RC-202IPV** not supplied*2Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequatepower handling capacities to avoid damage. Do not connect the speaker terminals to the car chassis, or connect theterminals of the right speakers with those of the left speakers. Do not connect the ground (earth) lead of this unit to the negative (–)terminal of a speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (withbuilt-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed inyour car if they feature a common negative (–) lead for the right and leftspeakers. Do not connect the unit’s speaker leads to each other.Notes on connection If “Output connection failure.” appears in the display, make sure thespeaker and amplifier are connected correctly. To use the monitor for the rear seats, connect the parking brake switchcord to the ground (earth).*4MonitorPower amplifierRear view cameraRear speakeriPodFront speakerSubwoofer Smartphone*1

/ 2

Related manuals for Sony XAV-601BT