Sony SRP-X700P Service Manual

Also see for SRP-X700P: User manual Interface manual Operating instructions Brochure Operating instructions

— 16 —15Default settingsINPUT OUTPUTItem Initial settingMIC1 - MIC4 –60 dBuTRIM MIC5/LINE1, MIC6/LINE2 +4 dBuLINE3, LINE4A - 4F –10 dBuLCFMIC1 - MIC4 ONMIC5/LINE1, MIC6/LINE2 OFFPEQ OFFFR OFFCOMP OFFMUTING OFFGAIN LIMIT +10 dBINPUT FADER 0 dBBand 1 63 HzMIC1 - MIC4FREQ Band 2 2.5 kHzMIC5/LINE1,Band 3 20 kHzMIC6/LINE2Band 1 1.0PEQQ Band 2 1.5Band 3 0.47GAIN Band 1 - 3 0 dBFREQBand 1 63 HzLINE3, LINE4Band 2 20 kHzPEQ QBand 1 1.0Band 2 0.47GAIN Band 1,2 0dBRouting Mix levelMIC1/WL1LINE OUT1, LINE OUT2 –20 dBLINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0dBMIC2/WL2LINE OUT1, LINE OUT2 –20 dBLINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0 dBMIC3LINE OUT1, LINE OUT2 –20 dBLINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0 dBMIC4LINE OUT1, LINE OUT2 –20 dBLINE OUT7, LINE OUT8, REC OUT1, REC OUT2 0 dBMIC5/LINE1 LINE OUT1, REC OUT1 0 dBMIC6/LINE2 LINE OUT2, REC OUT2 0 dBLINE3L LINE OUT1 0 dBR LINE OUT2 0 dBA⋅B⋅C⋅FL LINE OUT1, REC OUT1 0 dBR LINE OUT2, REC OUT2 0 dBL LINE OUT1, REC OUT1 0 dBLINE4 C LINE OUT5 0 dBD⋅E R LINE OUT2, REC OUT2 0 dBSW LINE OUT6 0 dBLS LINE OUT3 0 dBRS LINE OUT4 0 dBROUTING ATT LEVELSP OUTCH1 LINE OUT1 –10 dBCH2 LINE OUT2 –10 dBAUTOMATIC MIXER OFFROUTINGItem Initial settingOUTPUT1, OUTPUT2 +4 dBuREF LEVEL OUTPUT3 - OUTPUT8 –5 dBuREC OUT1, REC OUT2 –5 dBuHCF OFFEQ OFFDELAY 0 msMUTING OFFGAIN LIMIT +10 dBOUTPUT FADER 0 dBBand 1 25 HzBand 2 40 HzBand 3 80 HzBand 4 160 HzBand 5 315 HzOUTPUT1, FREQ Band 6 630 HzOUTPUT2 Band 7 1.25 kHzEQ Band 8 2.5 kHzBand 9 5 kHzBand 10 10 kHzBand 11 20 kHzQ Band 1 - 11 1.5GAIN Band 1 - 11 0 dBHCF OFFBand 1 63 HzFREQBand 2 250 HzBand 3 2.5 kHzOUTPUT3 - Band 4 20 kHzOUTPUT8 Band 1 1.0EQ Q Band 2, 3 1.5Band 4 0.47GAIN Band 1 - 4 0 dBHCF OFFMODE Lo Imp.SPEAKER SELECTCH1 OUTPUT 1OUTPUTCH2 OUTPUT 2ATTCH1 10 dBCH2 10 dB16Default settingsGROUP FADERItem Initial settingMASTER A MIC1/WL1, MIC2/WL2, MIC3, MIC4MASTER B MIC5/LINE1, MIC6/LINE2, LINE3, LINE4REMOTE1 - REMOTE6 Not assignedItem Initial settingINPUT1 AV SEL AINPUT2 AV SEL BINPUT3 AV SEL CINPUT4 AV SEL DINPUT5 AV SEL EINPUT INPUT6 AV SEL FINPUT7 RECALL 1INPUT8 RECALL 2INPUT9 RECALL 3INPUT10 LVL Master AINPUT11 LVL Master BPARALLEL I/OINPUT12 NONEOUTPUT1 AV SEL AOUTPUT2 AV SEL BOUTPUT3 AV SEL COUTPUT4 AV SEL DOUTPUT OUTPUT5 AV SEL EOUTPUT6 AV SEL FOUTPUT7 RECALL 1OUTPUT8 RECALL 2OUTPUT9 RECALL 1OUTPUT10 RECALL 2LINE3MACHINE TYPE MDCTRL S OUTPUT CH 1LINE4AMACHINE TYPE VTR3 (VHS)CTRL S OUTPUT CH 2LINE4BMACHINE TYPE VTR4 (DV)CTRL S OUTPUT CH 2LINE4CMACHINE TYPE NONEMACHINE CTRL S OUTPUT CH 1CONTROLLINE4DMACHINE TYPE DVDCTRL S OUTPUT CH 3LINE4E, MACHINE TYPE NONELINE4F CTRL S OUTPUT CH 1CH1 WIREDCONNECTION CH2 WIREDTYPE CH3 IRCH4 WIREDI/F TYPE RS-232CPROJECTOR PROTOCOL VPL-FX50PROJECTOR REMOTE POWER ENABLE ONCONTROLINPUT VIDEOLINE4A - LINE4C VIDEOTYPELINE4D COMPONENTLINE4E, LINE4F RGBREMOTETroubleshootingSymptomPower is not turned on.No sound is output.No microphone sound is output.Sound is distorted.No video comes out.The SRP-X700P cannot be controlledby RS-232C.PROTECTION indicator remains lit.Cause/Remedy• Power cord is disconnected.→ Firmly insert the power cord fully into the AC IN terminal and wall outlet.• Input fader is decreased.→ Increase the input fader.• Master volume is decreased.→ Increase the master volume.• ROUTING setup is incorrect.→ Set the ROUTING correctly using the SRP-X700P Manager.• MIC/LINE selector button is set to LINE.→ Set the MIC/LINE selector button to MIC.• The LINE equipment is connected to MIC5/LINE 1 IN and MIC6/LINE 2 IN terminalswhile the MIC/LINE selector button is set to the MIC position.→ Set the MIC/LINE selector button to LINE.• Video input signal setup is incorrect.→ Set the video input signal correctly again.• The cable routing method does not satisfy the specifications of this unit.• The RS-232C parameter settings do not satisfy the specifications of this unit.→ Connect cables following the instructions for “REMOTE RS-232C Terminal” described onpage 10.• When DC voltage appears in the SPEAKER terminal due to failure.→ Set the POWER switch to OFF.• If the heat sink temperature inside the amplifier exceeds the specified value.The connected speaker impedance is too low.→ Set the POWER switch to OFF and connect the SRP-X700P to a speaker having thecorrect impedance.Air intake and exhaust holes (on the right and left sides of the SRP-X700P) are chokedby dust.→ Clean the air intake and exhaust holes by removing dust with a vacuum cleaner.• Speaker terminal is short-circuited.→ Set the POWER switch to OFF and remove the cause of the short-circuit.Before contacting us, please check the following again. If the trouble persists, please contact your local Sony Sales office or Dealer.Start the supplied software SRP-X700P Manager and check the settings of the SRP-X700P. Check the following if the problem stillcannot be solved.