Sony MRW62E-S2 Operating Instructions Manual

Also see for Memory Stick MRW62E-S2: Read me first Operating instructions Operating instructions

4-260-058-11 (1)Operating InstructionsBefore operating the unit, please read this documentthoroughly, and retain it for future reference.Multi-CardReader/Writer© 2010 Sony Corporation Printed in Chinahttp://www.sony.net/MRW62E-S2TerminalWrite-ProtectedswitchLabel area3.3 V and 3 V type 5 V typeNotchTerminalMemo areaWrite-ProtectedswitchWARNINGKeep the unit away from children. If any part of theunit is swallowed, promptly see a doctor.To reduce the risk of fire or electric shock, do notexpose this apparatus to rain or moisture.To avoid electrical shock, do not open the cabinet.Refer servicing to qualified personnel only.CautionThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses, and can radiateradio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there is noguarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference toradio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the followingmeasures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician forhelp.You are cautioned that any changes or modifications notexpressly approved in this manual could void your authority tooperate this equipment.NoteIf you have any questions about this product, you may call thetelephone number listed in “Technical Support.” The telephonenumber below is not for customer service but only for officialpurposes.Declaration of ConformityTrade Name: SONYModel No.: MRW62EResponsible Party: Sony Electronics Inc.Address: 16530 Via Esprillo, San Diego, CA 92127U.S.A.Telephone No.: 858-942-2230This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions:(1) This device may not cause harmful interference, and (2)this device must accept any interference received, includinginterference that may cause undesired operation.NOTICE TO USERSDrive Letter Recognition Software ©2006 Sony Corporation.Documentation ©2006 Sony Corporation.All rights reserved. This manual or Drive Letter RecognitionSoftware described herein, in whole or in part, may not bereproduced, translated to any machine-readable form withoutprior written approval from Sony Corporation.IN NO EVENT SHALL SONY CORPORATION BE LIABLEFOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIALDAMAGES, WHETHER BASED ON TORT, CONTRACT, OROTHERWISE, ARISING OUT OF OR IN CONNECTION WITHTHIS MANUAL, THE DEVICE DRIVERS OR OTHERINFORMATION CONTAINED HEREIN OR THE USETHEREOF.Sony Corporation reserves the right to make any modification tothis manual or the information contained herein at any timewithout notice.SONY CORPORATION IS NOT RESPONSIBLE FOR ANYDAMAGE TO OR LOSS OF ANY PROGRAMS, DATA, OROTHER INFORMATION STORED ON ANY MEDIA.Copyright law prohibits unauthorized use of any recordedaudio/video for any other purpose than personal enjoyment.Please be warned that the “Memory Stick” containing imagesand data protected by copyright shall be strictly used withincopyright law.Trademarks• , “Memory Stick,” “Memory Stick Duo,” “MagicGateMemory Stick,” “Memory Stick PRO,” “Memory Stick PRODuo,” “Memory Stick PRO-HG Duo,” “Memory Stick Micro,”and “M2” are registered trademarks or trademarks of Sony.• Microsoft ®, Windows® , and the Windows logo are trademarksor registered trademarks of Microsoft Corporation in theUnited States of America and/or other countries.• Macintosh ® and Mac OS® are registered trademarks of AppleComputer, Inc. in the United States of America and/or othercountries.• Other system names, product names, and company namesappearing in this manual are trademarks or registeredtrademarks of their respective holders, even though notindicated by the ® or ™ marks.OverviewThe MRW62E-S2 (hereafter referred to as the “reader/writer”)has the following features:s Quick and simple data transfer - easily transfer images fromcamera to PCs Compatible with “Memory Stick,” “Memory Stick PRO,”“Memory Stick Duo,” CompactFlash, Microdrive, xD-PictureCard, SmartMedia, MultiMediaCard, SD Memory Cards Supports 17 different types of memory cardss Drive Letter Recognition Software can be downloaded fromthe web sites Quick to Connect - Hot-pluggable USB-powered designSystem RequirementsThe reader/writer requires the following minimum systemconfiguration:• OS– Windows ® 7– Windows Vista ®– Windows ® XP (Service Pack 2 or later)– Windows ® 2000 Professional (Service Pack 4 or later)– Windows ® Me– Mac OS X 10.2, 10.3, 10.4, 10.5, 10.6This product works with the standard drivers in Windows.Supported MediaThe reader/writer supports the following media:“Memory Stick” media• “Memory Stick” (without MagicGate) *1• “MagicGate Memory Stick” *1*2• “Memory Stick” (with MagicGate) *1*2*3• “Memory Stick Duo” (without MagicGate) *1• “MagicGate Memory Stick Duo” *1*2• “Memory Stick Duo” (with MagicGate) *1*2*3• “Memory Stick PRO” *2*3• “Memory Stick PRO Duo” *2*3• “Memory Stick PRO-HG Duo” *2*3• “Memory Stick Micro” (“M2”) *2*3*4*5*1 “MagicGate” is the general name of a copyright protection technologydeveloped by Sony.*2 Recording or playback of MagicGate data that uses MagicGatetechnology is not supported.*3 4-bit parallel data transfer is supported and the data read/write timingwill vary depending on the medium.*4 “M2” is an abbreviation of “Memory Stick Micro.” In this document,hereinafter, the abbreviation “M2,” is used.*5 With adaptor (not supplied) onlySD memory cards• SD/SDHC Memory Card *6• mini SD™ card *6*7*6 Recording or playback of data that uses SD technology is notsupported*7 With adaptor (not supplied) onlyOther memory cards• MultiMediaCard *8• RS-MMC *8• CompactFlash ®• Microdrive ® *9• SmartMedia™• xD-Picture Card™*8 MMCplus and MMCmobile are supported, but parallel data transfer isnot supported.*9 The Microdrive requires more power than other memory cards. Whenusing a Microdrive, remove other memory cards; otherwise an errormay occur due to a shortage of power.Notes• Not all memory cards are guaranteed to work. Operation isnot assured if non-supported memory cards are used.• The capacity of a file to be recorded/played back is smallerthan 4 GB per file according to the specifications of the filesystem incorporated in “Memory Stick.”• Although operation check of this product has been performedwith up to 8 GB “Memory Stick,” please note that theoperation is not guaranteed for every type of “Memory Stick.”• In this manual, all types of media listed in “Supported Media”are generically called memory cards.• I/O cards that are not memory cards, such as GPS cards, arenot supported.• MultiMediaCards and SD Memory Cards use the same slot, soyou cannot use them at the same time.• The “Memory Stick” media all use the same slot, so youcannot use them at the same time.• Only DOS format is supported. Memory cards in otherformats are not supported.About “Memory Stick” mediaWhat is “Memory Stick”?“Memory Stick” is a compact-size IC recording media with ahigh capacity. It has been designed not only exchanging/sharingdigital data among “Memory Stick” compliant products, butalso for serving as a removable external storage media that cansave data.Notes on “Memory Stick”On formatting (initialization)• If you format media in which data has been already written,all the data will be erased. Please be cautious not tomistakenly erase any important data.• Please make sure to format (initialize) media by the formatterof a “Memory Stick” compliant product. If it is initialized byWindows Explorer, it might become unusable on this product.About the size of “Memory Stick”• This product has a slot that can take both standard size andDuo size. All the products with such a slot as this areequipped with a system which automatically measures thesize of an inserted medium. That’s why both standard-size“Memory Stick” and smaller “Memory Stick Duo” can beused on this product without any Memory Stick DuoAdaptor.• Do not insert multiple “Memory Sticks” at the same time. Itmight cause damage to the product.• When you use “Memory Stick Duo” on this product, pleasemake sure to insert it in the right direction.• “Memory Stick Duo” should be kept away from smallchildren to prevent them from accidentally swallowing it.• When you use “Memory Stick Micro” on this product, pleasemake sure to attach the medium into M2 adaptor.If you attempt to insert “Memory Stick Micro” withoutattaching to M2 adaptor, there is a possibility that it cannot bepulled out.Usage Notes“Memory Stick” MediaNotes on using “Memory Stick” media• Do not remove “Memory Stick” while data is being read orwritten.• Data may be damaged if:– You remove “Memory Stick” or disconnect the USB cablewhile data is being read or written.– You use “Memory Stick” in a place where it is susceptibleto static electricity or electric noise.• You can keep backup copies of important data on a “MemoryStick.”• Avoid touching the metal terminals on the “Memory Stick” toprevent damage from static discharge.• Do not subject the “Memory Stick” to excessive stress orshock.• Do not disassemble or modify “Memory Stick.”• Keep “Memory Stick” and other media away from water,excessive heat and humidity, and from corrosive elements.• Do not use or keep “Memory Stick” under an unfavorablecondition as below:– Extremely hot place (such as in a parked car with windowsclosed in summer, a spot under direct sunlight, or near anelectrical appliance that radiates heat)– Humid place– Place near corrosive substances• If you set Write-Protected switch “LOCK,” data cannot berecorded, edited, or erased.• Do not stick anything other than the supplied labels on thelabel area of “Memory Stick.”• Stick a label precisely within the label area. Make sure that thelabel does not go beyond the area.• Carry and keep “Memory Stick” in the supplied case.Notes on using “Memory Stick Duo/MemoryStick PRO Duo”• When you use “Memory Stick Duo/Memory Stick PRO Duo”without Write-Protected switch, be careful not to edit or eraseimportant data by mistake.• When you use “Memory Stick Duo/Memory Stick PRO Duo”with Write-Protected switch, data cannot be recorded, edited,or erased by “LOCK” the switch.• Use an object with a sharp tip to move the Write-Protectedswitch.• Do not press on the memo area strongly when writing.• Carry and keep “Memory Stick” in the supplied case.SmartMedia CardsSupported SmartMedia cardsThe reader/writer supports 3.3-volt and 3-volt SmartMediacards, but not the older 5-volt type.NoteDo not insert a 5-volt SmartMedia card into the reader/writerforcibly.SmartMedia card handlingIf the gold contact area of a SmartMedia card is dirty, a readerror may occur. Keep the contact area clean. Otherwise do nottouch the gold contact area. Do not twist or warp the card.Protect the card from static electricity.SmartMedia card with IDThe reader/writer does not support the ID information onSmartMedia cards, but allows any SmartMedia card with an IDto be used as regular media.Other Points to NoteMedia formattingDo not format (initialize) memory cards with a computer. If youformat a memory card with a computer, devices such as digitalcameras may not be able to use it due to differences in formattype (FAT size, cluster size, hard disk type, or super floppy disktype). If you use a digital camera, format memory cards withyour camera, instead.Restrictions on DOS modeIn Windows, the reader/ writer does not operate in DOS mode.To use the reader/writer, start up Windows.StandbyThe reader/writer supports standby functions based on thePC2000 standard, which may not cover the standby function ofall computers. Disable the standby function of your computer ifit causes any problems. While the computer is in standby, do notinsert or remove any media.Do not attempt to dismantle, repair, or alter thereader/writer yourselfDo not, under any circumstances, attempt to dismantle, repair,or alter the reader/writer yourself. You may not onlypermanently damage the reader/writer and/or your computer,but may also cause fire or personal injury through electricalshock.Operating and storage environments• Do not place the reader/writer close to heat sources or indirect sunlight; in dusty, dirty, or humid locations; underprecipitation such as rain; or leave it in a hot vehicle with thewindows closed.• If the reader/writer interferes with the reception of radio ortelevision signals, move the reader/writer away from theradio or television.• When using the reader/writer, do not wrap it in cloth, sheets,or covers as this may cause a malfunction or fire.SpecificationsUSB transfer rateFull-speed (12 Mbps)High-speed (480 Mbps)This high-speed transfer rate is a theoretical value for the USBstandard.Actual performance is dependent on the device.Power requirements4.75 to 5.25 V DCCurrent consumptionMax. 500 mA *1Access indicatorAlways lit.Blinks on access.Operating environmentTemperature: 5°C to 40°C (41°F to 104°F)Humidity: 30% to 80% RHStorage environmentTemperature: -30°C to +60°C (-22°F to +140°F)Humidity: No condensationDimensions (W x H x D)Approx. 86 × 15.7 × 50 mm(3 3/ 8 × 5/ 8 × 2 inches) (excluding protrusions)MassApprox. 55 g (1.9 oz.) (TYP)*1 Except when using MicrodriveEnd User License AgreementIMPORTANT NOTICEThe following “END USER LICENSE AGREEMENT” applies tothe Drive Letter Recognition Software provided by Sony. Pleaseread the following “END USER LICENSE AGREEMENT” beforeinstalling. By installing the Drive Letter Recognition Software,you agree to the “END USER LICENSE AGREEMENT”.END USER LICENSE AGREEMENTThis is a legal agreement between you(hereafter referred to as the User) and Sony Corporation(hereafter referred to as Sony) pertaining to the right to use thesoftware (hereafter referred to as the PROGRAM). Using thePROGRAM indicates your acceptance of these terms andconclusion of the Agreement between the User and Sony.1 Copyright and all other rights relating to the PROGRAM anddocuments accompanying the PROGRAM are owned by Sonyor the original rightful person or organization (hereafterreferred to as the original rightful person) granting Sony theright to use the PROGRAM. The User is granted no rightsother than those specified in this agreement.2 Sony grants the User the non-exclusive, indivisible and non-transferable right to use the PROGRAM for the purpose ofusing the Sony product Multi-Card Reader/Writer for whichthe PROGRAM designates.3 The User may not transfer the Right of Use described above toany third party nor allow for any third party to use thePROGRAM unless the User obtains the advance writtenpermission of Sony.4 The User may not export or transport the PROGRAM ordocuments accompanying the PROGRAM from the countrywhere the User installed the PROGRAM to any other country.5 The User may not (i) update, add to, or modify nor (ii) de-assemble or de-compile the PROGRAM either in whole or inpart.6 THE PROGRAM IS PROVIDED “AS IS” WITHOUT EXPRESSOR IMPLIED WARRANTIES, INCLUDING WARRANTIESOF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE OR NON-DEFECTIVENESS.7 If any dispute relating to infringement of copyright, patent, orother intangible property rights arises between the User and athird party as a consequence of use of the PROGRAM, theUser shall settle the dispute at the User’s own expense, andshall make no claim against Sony or the original rightfulperson.8 Sony may terminate your license upon notice for failure tocomply with any of these Terms. Any such termination shallnot affect any payments, any compensation for damage. Upontermination, you must immediately destroy the Softwaretogether with all copies in any form.9 This Agreement has several non-English language versionsfor the reference purpose only. In the event of anydiscrepancy between the English language version and anyother language version, the English language version shallprevail.Package ContentsWhen you unpack the box, make sure that it contains all theaccessories listed below.If anything is missing or damaged, contact your retailer.• MRW62E-S2 Multi-Card Reader/Writer• USB cable• Operating InstructionsParts and FunctionsFront1 Access IndicatorThis indicator is always lit. The indicator blinks when thereader/writer accesses data on a memory card.2 SmartMedia / xD-Picture Card SlotInsert either a SmartMedia memory card or xD-Picture Cardhere.3 CompactFlash / Microdrive SlotInsert either a CompactFlash or Microdrive memory cardhere.Remove all other memory cards before using a Microdrive,because of its large power consumption.4 “Memory Stick” SlotInsert a “Memory Stick” media here.When inserting a “Memory Stick Micro” (“M2”), use anadaptor (not supplied).5 MultiMediaCard / SD Memory Card SlotInsert either a MultiMeidaCard or an SD Memory Card here.When inserting a miniSD Card, use an adaptor (notsupplied).Rear6 USB Port (mini B)Connect to a computer using the supplied USB cable.

/ 2

Related manuals for Sony Memory Stick MRW62E-S2