Sony IPELA SNC-CH210 Installation Manual

Also see for IPELA SNC-CH210: Quick reference Installation manual User guide Installation manual User guide

4-194-205-11 (1)Network CameraInstallation ManualBefore operating the unit, please read this manual thoroughly andretain it for future reference.使⽤⼿册使用产品前请仔细阅读本书，并请妥善保管。SNC-CH210EnglishOwner’s RecordThe model and serial numbers are located on the top. Record these numbersin the spaces provided below.Refer to these numbers whenever you call upon your Sony dealer regardingthis product.Model No. Serial No.WARNINGTo reduce a risk of fire or electric shock, do not exposethis product to rain or moisture.To avoid electrical shock, do not open the cabinet. Referservicing to qualified personnel only.WARNINGThis installation should be made by a qualified service person and shouldconform to all local codes.WARNING (for Installers only)Instructions for installing the equipment on the ceiling or the wall:After the installation, ensure the connection is capable of supporting at leasta force of 50 Newtons (N) downwards.CAUTION for LAN portFor safety reason, do not connect the LAN port to any network devices thatmight have excessive voltage.The LAN port of this unit is to be connected only to the devices whose powerfeeding meets the requirements for SELV (Safety Extra Low Voltage) andcomplies with Limited Power Source according to IEC 60950-1.Use IEEE802.3af standard compliant devices.For customers in the U.S.A.This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not cause harmfulinterference, and (2) this device must accept any interference received,including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limitsfor a Class A digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interferencewhen the equipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequency energy and, ifnot installed and used in accordance with the instruction manual, may causeharmful interference to radio communications. Operation of this equipmentin a residential area is likely to cause harmful interference in which case theuser will be required to correct the interference at his own expense.You are cautioned that any changes or modifications not expressly approvedin this manual could void your authority to operate this equipment.All interface cables used to connect peripherals must be shielded in order tocomply with the limits for a digital device pursuant to Subpart B or Part 15 ofFCC Rules.For customers in CanadaThis Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 duCanada.For the customers in EuropeThe manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan.The Authorized Representative for EMC and product safety is SonyDeutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.For any service or guarantee matters please refer to the addresses given inseparate service or guarantee documents.For the customers in Europe, Australia and New ZealandWARNINGThis is a Class A product. In a domestic environment, this product may causeradio interference in which case the user may be required to take adequatemeasures.In the case that interference should occur, consult your nearest authorizedSony service facility.This apparatus shall not be used in the residential area.ATTENTIONThe electromagnetic fields at specific frequencies may influence the pictureof the unit.Notes on UseBefore UseIf you find condensation before use, leave the camera out for long enoughand do not turn on the power until the condensation disappear.Remove static electricity before installation and operation.Data and securityYou should keep in mind that the images or audio you are monitoringmay be protected by privacy and other legal rights, and the responsibilityfor making sure you are complying with applicable laws is yours alone.Access to the images and audio is protected only by a user name and thepassword you set up. No further authentication is provided nor should youpresume that any other protective filtering is done by the service. Sincethe service is Internet-based, there is a risk that the image or audio you aremonitoring can be viewed or used by a third-party via the network.SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NOLIABILITY TO YOU OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS ORDISCONTINUATIONS OR EVEN SERVICE CANCELLATION. THE SERVICEIS PROVIDED AS-IS, AND SONY DISCLAIMS AND EXCLUDES ALLWARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE SERVICEINCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR THAT ITWILL OPERATE ERROR-FREE OR CONTINUOUSLY.Always make a test recording, and verify that it was recorded successfully.SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUTNOT LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OFFAILURE OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGESYSTEMS OR ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORDCONTENT OF ANY TYPE.Always verify that the unit is operating properly before use. SONY WILLNOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOTLIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THELOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THISUNIT, EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OFTHE WARRANTY, OR FOR ANY OTHER REASON WHATSOEVER.If you lose data by using this unit, SONY accepts no responsibility forrestoration of the data.Personal informationThe images taken by the system using this device can identify individualsand thus they fall under “personal information” stipulated in the “Act onthe Protection of Personal Information”. Please handle the video dataappropriately according to law.Information recorded using this product may also be “personal information”.Upon disposal, transfer, repair, or any other occasion where this product orstorage media is passed on to a third party, practice due care in its handling.Operating or storage locationAvoid operating or storing the camera in the following locations.Extremely hot or cold places (Operating temperature: 0°C to 50°C [32°F to122°F])Exposed to direct sunlight, or close to heating equipment (e.g., near heaters)Close to sources of strong magnetismClose to sources of powerful electromagnetic radiation, such as radios or TVtransmittersLocations subject to strong vibration or shockHumid or dusty locationsLocations exposed to rainLocations under the influence of fluorescent light or reflection of a windowUnder an unsteady light (The image will flicker.)VentilationTo prevent heat buildup, do not block air circulation around the camera.Power supplyThe power of this model is supplied by network cable.Use the network cable UTP, category-5.Damage to the network cable may result in fire or electric shock.TransportationAlways turn off the power when carrying.When transporting the camera, repack it as originally packed at the factory orin materials of equal quality.CleaningUse a blower to remove dust from the lens.Use a soft, dry cloth to clean the external surfaces of the camera. Stubbornstains can be removed using a soft cloth dampened with a small quantity ofdetergent solution, then wipe dry.Do not use volatile solvents such as alcohol, benzene or thinners as they maydamage the surface finishes.Note on laser beamsLaser beams may damage image sensors. You are cautioned that the surface of imagesensors should not be exposed to laser beam radiation in an environment where a laserbeam device is used.Phenomena Specific to Image SensorsThe following phenomena that may occur in images are specific to imagesensors. They do not indicate a malfunction.White flecksAlthough the image sensors are produced with high-precision technologies, finewhite flecks may be generated on the screen in rare cases, caused by cosmic rays,etc.This is related to the principle of image sensors and is not a malfunction.The white flecks especially tend to be seen in the following cases:- when operating at a high environmental temperature- when you have raised the gain (sensitivity)- when using the slow shutterAliasingWhen fine patterns, stripes, or lines are shot, they may appear jagged or flicker.About the Supplied ManualsInstallation Manual (this document)This Installation Manual describes the names and functions of parts and controlsof the Network Camera, gives connection examples and explains how to set upthe camera. Be sure to read the Installation Manual before operating.User’s Guide (stored in the CD-ROM)The User’s Guide describes how to set up the camera and how to control thecamera via a Web browser.After installing and connecting the camera correctly, operate referring to thisUser’s Guide.Using the CD-ROM ManualsThe supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.PreparationsThe Adobe Reader Version 6.0 or higher must be installed on your computer inorder to use the guides stored in the CD-ROM disc.NoteIf Adobe Reader is not installed, it may be downloaded from the following URL:http://www.adobe.com/Reading the manual in the CD-ROM1 Insert the CD-ROM in your CD-ROM drive.A cover page appears automatically in your Web browser.If it does not appear automatically in the Web browser, double-click on theindex.htm file on the CD-ROM.2 Select and click on the manual that you want to read.This opens the PDF file of the manual.Clicking an item in the Table of Contents allows you jump to the relevantpage.NotesThe files may not be displayed properly, depending on the version of AdobeReader. In this case, install the latest version, which you can download fromthe URL mentioned in “Preparations” above.If you have lost or damaged the CD-ROM, you can purchase replacement.Contact your Sony service representative.Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in theUnited States and/or other countries.(continued on the reverse side)中文产品名称：网络摄像机警告为减少⽕灾或电击危险，请勿让本设备受到⾬淋或受潮。为防⽌触电严禁拆开机壳，维修请咨询具备资格⼈⼠。警告本安装应该由有资格的服务⼈员进⾏，并须符合所有当地法规规定。警告（仅限于安装⼈员）有关在天花板或墙壁上安装设备的指示：安装后，请确保该连接至少可承受向下 50 牛顿 (N) 的拉力。局域网端口的注意事项为安全起见，切勿将局域网端口连接到可能有过高电压的网络设备。本机的局域网端口只能连接到供电符合 SELV（安全超低电压）要求和依照IEC 60950-1 符合 Limited Power Source（有限电源）要求的设备。使用 IEEE802.3af 标准兼容设备。声明此为 A 级产品，在⽣活环境中，该产品可能会造成⽆线电⼲扰。在这种情况下，可能需要用户对其⼲扰采取切实可⾏的措施。如果发⽣⼲扰，请咨询最近的 Sony 授权服务中⼼。注意某些特定频率的电磁场可能会⼲涉本装置的图像。使⽤注意事项使⽤前如果在使用前发现有湿气凝结，请将摄像机长时间搁置，直到湿气凝结消失后再打开电源。请在安装和操作前先去除静电。数据与安全请注意，您所监视的图像或⾳频可能受到个⼈隐私和其它合法权利的保护，并且您有责任确保您遵守相关法律。对图像和⾳频的访问仅由您所设定的用户名和密码保护。除此之外未提供其它⾝份验证⽅法，用户也不应该假定本服务提供了其它滤除功能。由于本服务基于互联网，会有第三者经由网络观看或使用监视中的影像或⾳频的危险。SONY 对于服务中断、不连续、甚至服务取消不承担责任。本服务按照原样提供，且 SONY 对于与服务相关的明示或暗示的保证不承担责任，包含但不仅限于任何对适销性、对特定用途的适用性或⽆故障连续使用的所有暗示保证。在记录前，请始终进⾏记录测试，并确认记录是否成功。SONY 对任何损坏概不负责。由于本机故障或由记录介质、外部存储系统或者任何其他介质或储存系统记录的任何形式的记录内容的损害不作（包括但不限于）退货或赔偿。在使用前请始终确认本机运⾏正常。⽆论保修期内外或基于任何理由，SONY 对任何损坏概不负责。由于本机故障造成的现有损失或预期利润损失，不作（包括但不限于）退货或赔偿。如果使用本机⽽造成数据丢失，SONY 不负责进⾏数据的恢复。个⼈信息使用本设备通过系统拍摄的影像能够识别个⼈，因此应归⼊“Act on theProtection of Personal Information（个⼈信息保护法）”中规定的“personal information（个⼈信息）”内。请按照法律正确处理视频数据。使用本产品记录的信息可能也是“personal information（个⼈信息）”。丢弃、转让、维修时或在本产品或存储媒体转交给第三⽅的任何其他场合，请⼩⼼处理。操作或存放场所避免在以下位置使用或存放摄像机。极热或极冷的地⽅（操作温度：0℃ 至 50℃）暴露于直射阳光下，或者靠近热源（⽐如加热器）的地⽅靠近强磁源的位置靠近⽆线电或电视发射器等强电磁辐射源的地⽅易于受到强力振动或撞击的地⽅潮湿或有灰尘的地⽅暴露于雨水的地⽅受到荧光灯或窗户反射光影响的地⽅在不稳定光线的下面（图像会抖动。）通风为了避免热量积蓄，不要阻挡摄像机附近的通风。电源本型号的电源由网线提供。使用 UTP、5 类网线。网线损坏可能会造成起火或触电。运送携带时务必关闭电源。当运送摄像机时，重新以出⼚时的包装进⾏包装，或用同等品质的材质包装。清洁用吹灰器清除镜头灰尘。使用柔软、⼲燥的布清洁摄像机的外表面。要清除顽固的污渍，请用少量清洁剂蘸湿软布，然后擦⼲即可。不要使用酒精、苯或稀释剂等挥发性溶剂，这些物质可能会破坏表面光洁度。有关激光束的注意事项激光束可能会损坏影像传感器。请注意：在使用激光束设备的环境中，影像传感器的表面不得暴露于激光束辐射中。影像传感器特有的现象影像中可能会出现以下影像传感器特有的现象。它们并⾮故障。⽩斑虽然图像传感器是采用高精度技术⽣产的，但由于宇宙射线等的影响，其屏幕上可能会出现细⼩的⽩斑（极少数情况）。这与图像传感器的原理有关，出现的⽩斑并不是故障。在以下情况中，⽐较容易出现⽩斑：- 在高温环境下进⾏操作时- 提高倍率（灵敏度）时- 当使用慢快门时图形失真拍摄微⼩的图案、条纹或线条时，它们可能呈锯齿状或出现闪烁现象。关于随附⼿册使⽤⼿册（本文档）本使用⼿册介绍网络摄像机各部件和控制器的名称和功能，连接示例和摄像机的设定⽅法。操作前请务必先阅读使用⼿册。⽤户指南（存储在 CD-ROM 中）用户指南介绍如何设定摄像机和如何通过网络浏览器控制摄像机。正确安装和连接摄像机后，请参照本用户指南操作。使⽤ CD-ROM ⼿册随附 CD-ROM 光盘包括 PDF 格式的本机用户指南。准备⼯作若要使用存储在 CD-ROM 光盘中的用户指南，则必须在电脑上安装 AdobeReader 6.0 或更高版本。注意如果未安装 Adobe Reader，可从下列 URL：http://www.adobe.com/ 下载。读取 CD-ROM 中的⼿册1 将 CD-ROM 插⼊ CD-ROM 驱动器。会在网络浏览器中⾃动出现封面页。如果没有在网络浏览器中⾃动出现封面页，请双击 CD-ROM 上的index.htm ⽂件。2 选择并单击您要读取的⼿册。这样即打开⼿册的 PDF ⽂件。单击⽬录上的项⽬可让您跳到相关页面。注意视 Adobe Reader 版本⽽定，可能⽆法正确显示⽂件。在此情况下，请安装最新版本，可从上述“准备⼯作”中提到的 URL 下载。如果您丢失或损坏 CD-ROM，可购买替换光盘。请联系您的 Sony 服务代表。Adobe 和 Adobe Reader 是 Adobe Systems Incorporated 在美国和/或其他国家的商标。（接反面） 2010 Sony Corporation Printed in China

/ 2

Related manuals for Sony IPELA SNC-CH210