Sony HS-KP1 Installer Manual

Contents

specifications

4-113-748-11(2)Installer’s manualKeypadHS-KP1©2008 Sony Corporation Printed in MalaysiaThis manual is for installers only.Contact your nearest installer for details on making the required connections for the system network.Before installation, refer to “System network” in the operating instructions of the Keypad to understand thewiring needed for the system.(2)PrecautionsCautionUnauthorized substitutions may result in fire, electric shock, or cause serious injury or death.Keep the following precautions in mind to prevent any accidents. Installment other than specified in the instructions may cause the unit to fall due to lack of wall strength. Do not use screws other than the supplied screws for installation. Do not install the unit following any procedure other than that explained in this manual. Make sure to followthe procedure in this manual closely. Do not disassemble the unit. Disassembly may cause a malfunction or cause injury. Do not place excessive pressure on the unit after mounting it. Damage may result, or it may cause injury.CAUTIONRISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONSOn power sourcesIf you are not going to use the unit for a long time, be sure to disconnect the unit from the wall outlet. Todisconnect the AC power cord, grasp the plug itself; never pull the cord.On placement The unit is designed for mounting only on the wall. You cannot mount it on the ceiling or on the floor. Place the unit in a location with adequate ventilation to prevent heat build-up in the unit. Do not place the unit on a soft surface, such as a rug. Do not place the unit near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanicalshock. Do not install the unit in an inclined position. It is designed to be operated in a vertical position only. Keep the unit away from equipment with strong magnets, such as microwave ovens, or large loudspeakers. Do not install the unit in a humid location, such as in a bathroom, or a place where moisture condensation mayoccur. Install the unit in a place where the environment falls within the operating temperature 0°C – 30°C(32°F – 86°F). Do not step on or place heavy objects on the unit. Damage may result, or it may cause injury. Installation into the wall should be done by Qualified Technicians.Unpacking HS-KP1 (1) Operating Instructions (1) Remote commander (1) R6 (size-AA) batteries (2) Installer’s manual (this manual) (1) Wall mounting bracket (1) Screws for the wall mounting bracket (long) (4) Screws for the unit (short) (2)The other units referred to in this manual are optional. Prepare necessary units depending on your system.Connecting RJ45 connectors to CAT5 cablesBefore you connect the CAT5 cables to the unit, you need to connect the RJ45 connectors to each end of thecables.Be sure to use Category 5e straight-through cables, and the wiring connection is correct. See the illustration belowfor details on connections.CAT5 cableWhite/OrangeWire colorOrangeWhite/GreenBlueWhite/BlueGreenWhite/BrownBrown1Pin No.2345678Note on installing CAT5 cablesThe following lengths of cable(s) can extend up to 200 feet: The combined length of the two longest cables connecting the Distribution Panel (HS-MB1) to an AV Wall Port(HS-WV1) and a Keypad (this unit). The length of cable connecting an AV Wall Port (HS-WV1) directly to a Keypad (this unit) without connectingthe Distribution Panel (HS-MB1). The length of cable connecting a Local Audio Wall Port (HS-WA1) to a Keypad (this unit).Connecting speaker cords or power supply cordsYou can connect up to two Keypads directly to a Power Supply (HS-AC1) in order to improve sound coverage ofthe Keypad. For details on Power Supply connection, refer to HS-AC1 manual.You can use any commercially available cord of gauge AWG 18 to AWG 26. AWG 18 cords are recommended assignal loss is less.1 Strip 10 mm (0.4 inches) of insulation off the cords and twist thebare wires together tightly.Be sure that the length of the bare wires is 10 mm (0.4 inches), matching the full-size illustration below.10 mm (0.4 inches)NoteDo not use a cord that is kinked, tarnished or otherwise damaged.2 While pressing down the orange tab next to the terminal, insertthe cord into the terminal as far as it will go. See the tables belowfor connections.ZONEMODEDC IN+ 19.5V GND R+R-L-L+SPEAKERSIMPEDANCE USE8 - 16HTIR REMOTEINCordRear of the unita b ABCDThis unitDC INPower SupplyDC OUTThis unit Your speakersDC 19.5 V – a 19.5 V R+/- – A/B R+/-GND – b GND L-/+ – C/D L-/+Notes To press down the orange tab, a slim object such as a flathead screwdriver can be used. Be sure to connect the terminals correctly as shown in the table above. If a speaker cord is reversed, thesound may be distorted. Make sure none of the bare wires touch each other. If they do, it may cause a short-circuit, which coulddamage the system.Part names and descriptionsZONEMODEDC IN+ 19.5V GND R+R-L-L+SPEAKERSIMPEDANCE USE8 - 16HTIR REMOTEINRear of the unitHS-WA1TO LOCAL AUDIOWALL PORTHS-WV1TO DISTRIBUTION PANELHS-MB1TO AV WALL PORTTop of the unit RJ45 terminals (, )Connect the unit to Local Audio Wall Port (HS-WA1) using CAT5 cables so that the letters (, ) indicatedon both the units match each other. RJ45 terminals (, )Connect the unit to Distribution Panel (HS-MB1) or AV Wall Port (HS-WV1) using CAT5 cables so that theletters (, ) indicated on both the units match each other. SPEAKERSConnect speakers (nominal impedance 8 ohms or higher) in a room using a speaker cord. See “Connectingspeaker cords or power supply cords.” DC INConnect DC IN of Keypad to DC OUT of Power Supply (HS-AC1) using a power supply cord. See“Connecting speaker cords or power supply cords.” A DC power source is supplied to the Keypad through theAWG 24 cords inside the CAT5 cable connected to . However, sound quality of the Keypad may deteriorateif cables are long, due to power loss through the cable. For optimum sound quality, connect directly Keypadand Power Supply using thicker cords than AWG 24, up to AWG 18. MODE (ZONE/HT) switchSwitch between ZONE mode and HT mode. The ZONE mode is used to select input sources. The HT modecan be used for basic operations on the Multi Channel AV receiver. For further details on these modes, refer tothe Keypad operating instructions. IR REMOTE INConnect an IR sensor.

/ 2

Related manuals for Sony HS-KP1