Sony DVP-NW50 Installer Manual

Also see for CDP-NW10 - Compact Disc Player: User manual Installation User manual Dimension Guide Installer manual

2-584-980-11(2)Inst aller’s manual© 2005 Sony Corporation Printed in KoreaConnect ing a com put erConnect each Unit and a computer using an Ethernet cable(100Base-TX, optional.) For details on the connection, refer to“Hooking up the sysytem” on this manual and the instructionmanual supplied with your router or hub.Connect ing a TV (DVP-NW50 only)Connections between the Unit and each of devices are made viacables or cords coming through the wall.Connect the Unit to a TV or a projector using the VIDEO cord.Select one of the ways of connection methods shown below,according to the input jack on your TV.Precaut ionsCaut ionUnauthorized substitutions may result in fire, electric shock,causing die or serious injury.Keep the following precautions in mind to prevent any accidents.• Installment and settings other than that of specifiedinstructions may cause the unit to fall due to lack of strength ofthe wall.• Do not use screws other than the supplied screws forinstallation.• Do not install the unit following any procedure other than thatexplained in this manual. Make sure to follow the procedure inthis manual closely.• Do not disassemble the unit. This may cause a malfunction ofthe unit or cause injury to you.• Do not apply strong pressure on the unit after mounting it. Theunit may be damaged or fall, causing a injury to you.On pow er sources• The Unit is not disconnected from the AC power source as longas it is connected to the wall outlet, even if the player itself hasbeen turned off.• If you are not going to use the Unit for a long time, be sure todisconnect the Unit from the wall outlet. To disconnect the ACpower cord, grasp the plug itself; never pull the cord.UnpackingItem CDP-NW10 DVP-NW50CDP-NW10 Unit 1 –DVP-NW50 Unit – 1Remote commander (remote) 1 1(RM-ANU001 )Wall mounting bracket 1 1Wall stopper 4 4TEMPLATE 1 1Plug-in 4P terminal (for speakers) 1 3Plug-in 5P terminal 1 –(for AC power unit)Plug-in 6P terminal – 1(for AC power unit)Screws for fixing the Unit to 4 4the wall mounting bracket (short)Screws for wall stopper (long) 4 4AM loop antenna (aerial) 1 1R6 (size-AA) battery 2 2User’s manual 1 1Installer’s manual (this manual) 1 1CDP-NW10/DVP-NW50 Syst emNet w orkThe diagram below illustrates an entire system network made upwith multiple Units.NoteThe configuration shown below is for illustrative purpose only. It differsfrom an actual system network.Custom IntegratedAV SystemOn placement• The Unit is designed for mounting only on the wall. You cannotmount it on the ceiling or on the floor.• Place the Unit in a location with adequate ventilation toprevent heat build-up in the Unit.• Do not place the Unit on a soft surface such as a rug.• Do not place the Unit in a location near heat sources, or in aplace subject to direct sunlight, excessive dust, or mechanicalshock.• Do not install the Unit in an inclined position. It is designed tobe operated in a horizontal position only.• Keep the Unit and the discs away from equipment with strongmagnets, such as microwave ovens, or large loudspeakers.• Do not install the unit in a humid location, such as in abathroom, or a place where moisture condensation may occur.Install the Unit in a place where the environment falls withinthe operating temperature 0˚C – 40˚C (32˚F – 104˚F).• Do not step on or place heavy objects on the unit. The unit maybe damaged or fall, causing injury to you.KITCHENCDP-NW 10GUEST ROOMBEDROOMCDP-NW 10CDP-NW 10ComputerHubRouterINTERNETCD ChangerTV/ ProjectorFrontSpeakerFrontSpeaker DVP-NW 50RearSpeakerLIVING ROOMSub W ooferCenterSpeakerRearSpeakerExample of t he DVP-NW50 syst em net w orkNoteDo not connect a VCR, etc., between your TV and the player. If you passthe player signals via the VCR, you may not receive a clear image on theTV screen. If your TV has only one video input jack, connect the Unit tothis jack.Connect ing audio Equipm entConnections between the Unit and each of devices are made viacables or cords coming through the wall.The Unit can input sound from external audio equipment via theaudio connectors on the Unit. Connect the OUTPUT jacks (L/R)of the audio equipment to the LINE IN (L/R) jacks of the Unitusing the proper audio cords (optional).Connect ing an IR IN/OUTConnections between the Unit and each of devices are made viacables or cords coming through the wall.You can operate a component using the remote if the IR IN/OUTterminal of the Unit and the component are connected. Forexample, if you connect IR IN of the Unit and IR OUT of a TV,you can operate the Unit with the remote by aiming it at the TV.If you connect IR OUT of the Unit and IR IN of a component,such as a DVD Changer, you can operate the DVD Changer withthe remote (supplied with the DVD Changer) by aiming it at theUnit.Connect ing an AC pow er unitAfter connecting the Unit and the AC power unit using thepower supply cables, connect the AC power cord to the AC IN ofthe AC power unit, then the other end of the AC power cord tothe wall outlet.Inst alling t he UnitBefore installing the Unit into the wall, take steps to ensure yoursafety and that of your surroundings, then check the following:• The location of the power source to make sure that power supply cablecan reach from the Unit.• The location of the speakers to make sure that speaker cords can be runbetween the Unit and the speakers.• The distance between the Unit and the AC power unit (up to 200 feet(60 m)).• The durability of the wall (The thickness of the wall must be between1/2 to 3/4 inches. (13 mm to 19 mm)).• There are no obstructions, such as an air, an electrical, or a waterconduit near the location where the Unit is installed.• There is enough space (over 6 inches (15 cm)) inside the wall. If thespace available inside the wall is insufficient or does not have properventilation, a malfunction of the Unit may occur due to heat build-up.• Do not install the Unit where the Unit may get wet due to water orother liquid. This may cause a malfunction of the Unit.• Do not install the Unit in a place where moisture condensation maycause a malfunction of the Unit.Inst alling bracket s f or new const ruct ion (bef orew all const ruct ion is f inished)You may install a pre-construction bracket on the studs where theunit will be installed. It is recommended that you use a pre-construction bracket when you install the unit in a house that isstill under construction. However, the pre-construction bracket isonly for the use of sub installation. You may not be able to use thepre-construction bracket on the place where the wall and materialof the wall and pillar may be damaged or some other problemsmay occur.NoteThe following items are included in the Pre-construction bracket kit (WS-BKT1).• Pre-construction bracket (1)• Wings (2)• AM Antenna (1)• Screws for the AM Antenna (2)• Manual (1)1 Insert the tw o w ings into the tabs of the pre-constructionbracket.2 Place the pre-construction bracket on the studs, and thenfasten the screw s (not supplied) to attach the pre-construction bracket.W ingTipRun the cables into the hole marked with an “*” in the illustrationabove, so that you can bundle and fix the cables.Notes• Make sure that the pre-construction bracket is properly level, bothhorizontally and vertically. Improper positioning may cause theunit to fall, or may cause difficulty when you install the Unit.• Make sure that more than 4 inches (10 cm) of space is availablebehind the wall for installing the unit.3 Place the AM loop antenna on the stud, and then fastenthe supplied screw s to attach it. Raise the entire AMantenna, and then insert its tab into the notch to set upthe AM loop antenna.Take care to attach the AM loop antenna on the stud as faraway from the CDP-NW10, DVP-NW50, or other electricaldevices as possible (at least 1 foot (30 cm)).4 After the w all construction is finished, cut the outlinealong the inside edge of the pre-construction bracket.Do not cut over or beyond the edge.Before proceeding to step 4, make sure that all the necessarycables can be run to the bracket location.NoteMake sure that the size of the hole cut in the wall corresponds to thespecified size (height: 83/8 X 87/16 inches, 212.5 - 215 mm), (width:83/16 X 81/4 inches, 207.5 - 210 mm). If the hole is too big to mountthe bracket, the Unit may fall and cause an accident.5 Place the mounting bracket over the hole so that the pre-construction bracket and the mounting bracket matchacross the w all. Then fasten the w all mounting bracketscrew s carefully to fix the mounting bracket and pre-construction bracket so that they are level and alignperfectly.Make sure the larger tab is mounted at the bottom.Notes• Fasten the screws securely. Failure to fasten the screws orincomplete tightening of the screws may cause the Unit to fall andcause an accident.• For mounting the bracket, use the supplied screws.To m ount t he unit on t he f inished w all1 M ark the location w here the Unit is to be installed on thew all using the supplied TEM PLATE (83/ 8 X 81/ 4 inches (212.5mm X 207.5 mm)).Make sure the mark is properly level, horizontally andvertically.2 Cut the outline along the mark, then carefully cut a cleanhole through the w all.Notes• Do not cut over or beyond the outline.• Make sure that the size if the hole cut in the wall corresponds to thespecified size. If the hole is too big to mount the bracket, the Unitmay fall and cause an accident.• Do not make a gap between the wall and the mounting bracket.3 Rotate the stoppers to the inside of the frame, and thenplace the mounting bracket over the hole.Make sure the larger tab is mounted at the bottom.4 Rotate the stoppers to the outside of the frame behindthe w all.5 Fasten the w all mounting bracket screw s carefully so thatthe w all mounting bracket is level.Notes• Fasten the screws securely. Failure to fasten the screws orincomplete tightening of the screws may cause the Unit to fall andcause an accident.• For mounting the bracket, use the supplied screws.Larger tabLarger tab*This manual is for installers only.Contact your nearest installer for details on makingthe required connections for the system network.Downloaded from: https://www.usersmanualguide.com/

/ 3

Related manuals for Sony CDP-NW10 - Compact Disc Player