Menu
Sony DVP-NS300 Service Manual
Also see for DVP-NS300: Training manualOperating instructionsOperating instructionsOperating instructionsSpecifications
                                                                                                               | |
Contents
|
6-76-5. DRIVE MANUAL OPERATIONOn the Test Mode Menu screen, select [2], and the manual opera-tion menu will be displayed. For the manual operation, each servoon/off control and adjustment can be executed manually.## Drive Manual Operation ##Operation Menu1. Disc type2. Servo Control3. Track/Layer Jump4. Manual Adjustment5. Auto Adjustment6. Memory Check0. Disc Check MemoryExit: RETURNIn using the manual operation menu, take care of the followingpoints. These commands do not provide protection, thus requiringcorrect operation. The sector address or time code field is dis-played when a disc is loaded.1. Set correctly the disc type to be used on the Disc Typescreen.The disc type must be set after a disc was loaded.The set disc type is cleared when the tray is opened.2. After power ON, if the Drive Manual Operation was se-lected, first perform “Reset SLED TILT” by opening 1.Disc Type screen.3. In case of an alarm, immediately press the [STOP] but-ton to stop the servo operation, and turn the power OFF.Basic operation (controllable from front panel or remote com-mander)[POWER] Power OFF[STOP] Servo stop[OPEN/CLOSE] Stop+Eject/Loading[RETURN] Return to Operation Menu or Test ModeMenu[NEXT], [PREV] Transition between sub modes of menu[1] to [9], [0] Selection of menu itemsCursor UP/DOWN Increase/Decrease in manually adjustedvalue0. Disc Check MemoryDisc Check1. SL Disc Check2. CD Disc Check3. DL Disc Check0. Reset SLED TILTOn this screen, the mirror time is measured and written to theEEPROM to check the disc type. First, set a DVD SL disc andpress [1], then set a CD disc and press [2], and finally set a DVDDL disc and press [3]. The measured mirror time is displayed re-spectively.The adjustment must be executed more than once after defaultdata were written.Reference value for DVD is from 10 to 20, and for CD, from 28 to4F. Check that the value of CD is larger than that of DVD. Whenthose values are beyond a range perform this adjustment again.From this screen, you can go to another mode by pressing [NEXT]or [PREV] key, but you cannot enter this mode from another mode.You can enter this mode from the Operation Menu screen only.1. Disc TypeDisc Type1. Disc Type Auto Check2. DVD SL 12 cm3. DVD DL 12 cm4. CD 12cm5. LCD 12 cm6. DVD SL 8 cm7. DVD DL 8 cm8. CD 8 cm9. LCD 8 cm0. Reset SLED TILTEMG. 00On this screen, select the disc type. To select the disc type, pressthe number of the loaded disc. The selected disc type is displayedat the bottom. Selecting [1] automatically selects and displays thedisc type. In case of wrong display, retry “Disc Check Memory”.Also, opening the tray causes the set disc type to be cleared. Inthis case, set the disc type again after loading.In performing manual operation, the disc type must be set.Once the disc type has been selected, the sector address or timecode display field will appear as shown below. These values aredisplayed when PLL is locked.Disc Type1. Disc Type Auto Check2. DVD SL 12 cm3. DVD DL 12 cm4. CD 12cm5. LCD 12 cm6. DVD SL 8 cm7. DVD DL 8 cm8. CD 8 cm9. LCD 8 cm0. Reset SLED TILTSA.------ SI.-- EMG. 00DVD SL 12 cmDisplay when DVD SL 12cm disc was selectedwww. xiaoyu163. comQQ 376315150 992894298TEL 13942296513 992894298051513673QQTEL 13942296513 QQ 376315150 892498299TEL 13942296513 QQ 376315150 892498299http://www.xiaoyu163.comhttp://www.xiaoyu163.com |
Related manuals for Sony DVP-NS300
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved