Sony Cybershot,Cyber-shot DSC-U60 Operating Instructions Manual

Also see for Cyber-shot DSC-S600: Operating instructions Supplemental instructions Specifications Specifications Software guide

DSC-U60Sony Corporation © 2003 Printed in Japan 3-082-427-11(1)IMPORTANT!WaterproofspecificationsNotes on waterproofperformanceThis camera conforms to IEC60529 IPX6* and IPX7**, and can beused in places exposed to splashing water or underwater up todepths of 1.5 m (5 feet).* Water shall not enter the interior even when exposed to direct jet streamsof water (normal temperature fresh water) from any direction.** Water shall not seep into the interior even when left submerged innormal temperature fresh water at a depth of 1 m (3 feet 3 1/4 inches) ina stationary condition for approximately 30 minutes.You can use this camera in the following places:Underwater (ocean, swimming pools) up to depths of 1.5 m (5 feet),beachside, riverside, poolside, ski slopes, in the rain, etc.Do not use this camera in the following places:Places where the camera might be subject to high water pressure,hot springs or bathtubs, etc.Notes on use• Before using this camera underwater or in places exposed towater, be sure to inspect the O-ring and the O-ring mating surfaceon the inside of the camera.• Do not immerse the camera in water containing soap, detergent,bath salts, etc., or in hot water with a temperature of more than30°C.• Never open the waterproof cover underwater or in places exposedto water.Lock the lock switch to prevent the waterproof cover from opening byaccident.• This camera does not float in water.• Before opening the waterproof cover, be sure to rinse off anysand and completely wipe away any water that may be present onthe camera body.• Should you find any evidence of water leaks inside thewaterproof cover, stop using the camera at once and contact yourSony dealer or local authorized Sony service facility.• Sony cannot be held responsible for malfunctions or irreparableproblems arising from water or foreign objects entering the insideof the camera due to improper handling.• Note that waterproof performance is not guaranteed under allenvironments and conditions.English On the O-ringO-rings are a type of waterproof packing that is used in underwatercameras and watches, diving equipment, etc. This camera uses anO-ring in the waterproof cover portion.Before useBefore using this camera underwater or in places exposed to water,be sure to inspect the O-ring and the O-ring mating surface.If the O-ring or the O-ring mating surface is cracked, scratched orotherwise damaged, or if sand particles, hair or other minute dirt hasadhered, the waterproofing performance may be impaired. Notethat water entering the inside of the camera may cause irreparabledamage.5O-ring mating surfaceO-ringInspecting the O-ring and the O-ring matingsurfaceInspect the O-ring and the O-ring mating surface in a location thatis free from sand, dust or moisture.1 Before opening the waterproof cover, rinse off anysand and completely wipe away any water thatmay be present on the camera body.• Sand or water getting inside the camera may cause amalfunction.2 Open the waterproof cover.• For details on how to open and close the waterproof cover,see page 12 in the operating instructions.3 Inspect the O-ring and the O-ring mating surface.• Be sure to wipe away any dirt, sand particles, hair, dust, salt,lint or other foreign matter adhering to the O-ring with a soft,lint-free cloth. Even a single hair adhering to the O-ring maycause a water leak.• Tiny dirt particles that are difficult to see may have adheredto the O-ring, so inspect the O-ring by running it throughyour fingers.• When wiping away dirt from the O-ring, take care that clothfibers do not remain on the O-ring.• When it is difficult to wipe away the dirt from the O-ring,remove the O-ring and wash it with water.• Be sure to replace the O-ring with a new one if it becomescracked, warped, crushed, twisted, split, scratched, rough orotherwise damaged.4 Close the waterproof cover.5 Lock the lock switch.Dirt Sand Hair DustSalt LintCrack Warp Crush TwistSplit Scratch RoughRemoving/Setting the O-ringWhen removing the O-ring for replacement, cleaning or inspection,take care for the following points.Removing the O-ringPress lightly on the O-ring with your fingers to shift it from thegroove, grasp the slack portion, and remove the O-ring.• Do not use a pointed, sharp or metal object to remove the O-ring.This can scratch the O-ring or the O-ring mating surface whichmay allow water to leak inside the camera.• Do not place excessive tension on the O-ring.Cleaning the O-ring and the O-ring groove• Use tap water at 30°C or less to wash the O-ring that youremoved. Wipe away any water when finished.• The O-ring is specially treated, so take care not to allow grease oroil to adhere to the O-ring.• When sand particles or encrusted salt may be present in the O-ring groove, clean the groove carefully using a cotton swab. Takecare that fibers from the cotton swab do not remain in the groove.• Do not use a pointed, sharp or metal object for cleaning, as thismay scratch the O-ring groove.Setting the O-ringPlace the O-ring in the groove, taking care for the following points.• Do not place excessive tension on the O-ring.• After setting, run a final check for any of the following problems.– Are there any water droplets on the O-ring?– Is the O-ring twisted?– Has any dirt, etc. adhered to the O-ring?– Is the O-ring protruding from the groove?O-ring life• Replace the O-ring with a new one if it becomes cracked, warped,crushed, twisted, split, scratched, rough or otherwise damaged.Even if the O-ring has no problems, deformation and wear overtime can cause the waterproof performance to drop, so replace theO-ring with a new one after approximately two years of use.• Consult your Sony dealer or local authorized Sony servicefacility for replacement of O-rings. Order the following partsnumber when purchasing the O-ring:“3-081-956- ”Cleaning after useAfter getting the camera wet• Wipe away any water droplets on the camera body with a clean,dry, soft cloth.• Note that water remaining in the gaps on the camera body mayget your clothes or the inside of your bag wet.• In cold places, water droplets may freeze on the camera body.Note that using the camera with water droplets frozen on it maycause a malfunction.When sand, dirt or seawater adhere to thecameraIf salt or other dirt is left encrusted on the camera, the metalportions may become damaged or rusted and result in water leaks.Follow the procedure below and clean the camera before openingthe waterproof cover. Use tap water at 30°C or less to wash thecamera.1 Leave the camera immersed in a bucket or othercontainer filled with fresh water.• Wash the camera by gently moving it back and forth tothoroughly remove any dirt, sand and salt. Then, let it soakfor approximately 30 minutes.• Do not rub the lens or the LCD screen when they are dirty asthis may cause scratches.2 Wipe the camera.• Wipe away the water on the camera using a clean, dry, softcloth, then leave the camera in the shade to dry.• Water that is not completely wiped away may seep out later,so place the camera on a soft cloth.Other precautions• If there is mud on the O-ring, or if the camera has been inseawater, remove the O-ring to clean and inspect it.• When sun oil or other oily substances adhere to the camera, washthe camera in tap water. Leaving these substances on the cameramay cause surface discoloration or other damage.• Do not wash the camera in a washing machine, etc.• Do not swing the camera violently to shake off the water orforcibly dry the camera using a hair dryer, etc.• When the O-ring or the O-ring mating surface is extremely dirty,consult your Sony dealer or local authorized Sony servicefacility.On storageAvoid storage in hot, cold or humid places, or places exposed tonaphthalene, camphor or other chemicals, as this may damage thecamera.

/ 1

Related manuals for Sony Cyber-shot DSC-S600