OneStart

Menu
Siemens VIS3I-328 Installation Manual Manual pdf 50 page image

Siemens VIS3I-328 Installation Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Safety
  4. Meaning of the signal words
  5. Technical data
  6. Mechanical dimensions
  7. Details for ordering
  8. Description of equipment
  9. Enclosure
  10. Printed circuit boards (PCBs)
  11. Power supply module VIS3I-PSU
  12. Cooling fan
  13. Front panel indicators
  14. Rear panel connections and controls
  15. Firmware and software
  16. Quad card VIS3-QUAD
  17. Installation
  18. Connecting two VIS3I-328 units for expansion
  19. Commissioning
  20. Set VisiPC default product to integrated
  21. Confirm software versions
  22. VisiPC self-test
  23. Load new configuration as necessary
  24. System integration
  25. Connecting CKA Keyboards
  26. Connecting alarm inputs
  27. Connecting a VCR/DVR and multiplexer
  28. Connecting a quad card output to a video input
  29. Distributed video switching using a VisiWire or PCCON network
  30. Determining how VIS3I-328 unit nodes can be networked
  31. Configuring network alarms
  32. Connecting VIS3I-328 to Visilynx 2 nodes using PCCON
  33. Controlling 256 cameras x 64 monitors (banked switching; not full cross point)
  34. Controlling 64 cameras x 64 monitors (full cross point)
  35. Controlling via the Video Management Software IVM
  36. Maintenance and service
  37. Fault indications
  38. System fault-finding process
  39. Self-test alarms
  40. VisiPC self-tests
  41. Disposal
Siemens VIS3I-328 Installation Manual Manual pdf 50 page image
50Siemens Building TechnologiesFire Safety & Security Products 10.200810.3.4 VisiPC self-testsA full list of all the VisiPC self-tests that can be selected is contained in Tab. 38.Refer to the VisiPC Software User Manual for full details.VisiPC SettingsTest Type Test LevelHardwareRequiredPrecautions DescriptionAll start-up tests None Repeats all start-uptestAll internal tests None Serial input signalsshould be removed ordisabled during testingTests all internaldevicesAll testsAll external tests Loopback connectors fittedto all serial portsSee Tab. 39 Tests serial ports vialoopbacksAddress decoder Unused NoneAll Flash areas None Tests all thefollowing areasFBL software None Test Flash BootLoader softwareController software None Tests ControllerSoftwareFPGA data None Tests FPGA dataUser Config data NoneFlashNote: A failure of User Config data is indicated if config data has not been loaded – thisdoes not indicate a hardware fault.Tests Fixed,Variable and Defaultconfiguration data.Do not save results None Re-detects optioncardsSave results to flash None Required if cards havebeen changed andconfig data notreloadedAuto-detecthardwareTip: Saving auto-detection results to flash is a quicker way of registering changes inoption card positions than re-loading configuration data, but has the same effect.Re-detects optioncards and savesresults to Flash.SRAM Unused None Tests all static RAMmemoryUnused NoneBattery-backedSRAM Note: A failure of Battery-Backed SRAM is indicated after loading new config data – thiscan be ignored. Press the rear panel CPU reset button and repeat the test.Tests all battery-backed SRAM, usedfor holding matrixstate while powereddownInternal loopback None Serial input signalsshould be removed ordisabled during testingTests all serial portsusing internalloopback switchingSerial portsExternal loopback Loopback connectors fittedto all serial portsSee Tab. 39 Tests all serial portconnections viaexternal loopbackconnectorsReal-time clock Unused None Tests the clockdeviceSCB registers Unused None Tests internal SerialControl Buscommunication
/ 56
This manual is suitable for:
VIS3I-328Visilynx 3
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved