sUser GuideTC35 Terminalwww.siemens.com/wm be inspired WirelessModuleswww.siemens.com/wm

Safety information

Overview

Product description

Highlights

Features

External interfaces

Installation

Interface description

Handset connector

Antenna connector FME (male)

RS232 interface

Startup

Operating states / LED

POWER DOWN

Network search

AT command control

SW update

Compatibility

Certification / maintenance

Index

Siemens TC35 Terminal User Manual

Safety and installation information

TC35

ront view

Product data

eatures

Plug-in power supply unit

Antenna connector ME (male)

Version History

Introduction

Conventions

Combining AT commands on the same command line

Supported character sets

Flow control

Standard V.25ter AT Commands

ATQn Flowcontrol

ATD Mobile originated call to dial a number

ATD><mem><n> Originate call to phone number <n> in memory <mem

ATD><n> Originate call to phone number selected from active memory

ATD><str> Originate call to phone number in memory with corresponding field

ATDI Mobile originated call to dialable ISDN number <n

ATDL Redial last telephone number used

ATE Enable command echo

ATI Display product identification information

ATL Set monitor speaker loudness

ATQ Set result code presentation mode

ATS2 Escape code sequence

ATS5 Write command line editing character

ATS7 Set number of seconds to wait for connection completion

ATS10 Set disconnect delay after indicating the absence of data carrier

ATV Set result code format mode

ATZ Set all current parameters to user defined profile

AT&D Set circuit Data Terminal Ready (DTR) function mode

AT&S Set circuit Data Set Ready (DSR) function mode

AT&V Display current configuration

AT&W Store current configuration to user defined profile

AT+GCAP Request complete TA capabilities list

AT+GMR Request TA revision identification of software status

AT+ILRR Set TE-TA local rate reporting

AT+IPR Set fixed local rate

Autobauding

AT Commands for FAX

AT+FBADMUL Error Threshold Multiplier

AT+FCIG Query or set the Local polling id

AT+FCQ Copy Quality Checking

AT+FDCC Query or set capabilities

AT+FDFFC Data Compression Format Conversion

AT+FDIS Query or set session parameters

AT+FDR Begin or continue phase C data reception

AT+FET End a page or document

AT+FMDL Identify Product Model

AT+FPHCTO DTE Phase C Response Timeout

AT+FRM Receive Data

AT+FTM Transmit Data

AT+FVRFC Vertical resolution format conversion

AT Commands originating from GSM 07.07

AT+CALA Set alarm time

AT+CAMM Accumulated call meter maximum (ACMmax) set or query

AT+CAOC Advice of Charge information

AT+CBST Select bearer service type

AT+CCFC Call forwarding number and conditions control

Examples: Call forwarding

AT+CCLK Real Time Clock

AT+CEER Extended error report

AT+CFUN Set phone functionality

AT+CGMI Request manufacturer identification

AT+CGSN Request product serial number identification (IMEI) identical to GSN

AT+CHUP Hang up call

AT+CLCC List current calls of ME

AT+CLCK Facility lock

Examples: Enabling / disabling PIN 1 authentication

Examples: Call barring

AT+CLIP Calling line identification presentation

AT+CLIR Calling line identification restriction (by *# sequence)

AT+CLVL Loudspeaker volume level

AT+CMEE Report mobile equipment error

AT+CMUT Mute control

AT+CMUX Enter multiplex mode

Restricted use of AT commands in Multiplex mode

AT+COPN Read operator names

AT+COPS Operator selection

AT+CPAS Mobile equipment activity status

AT+CPBR Read current phonebook entries

AT+CPBS Select phonebook memory storage

AT+CPBW Write phonebook entry

AT+CPIN Enter PIN

What to do if PIN or password authentication fails

AT+CPIN2 Enter PIN2

AT+CPUC Price per unit and currency table

AT+CPWD Change password

AT+CR Service reporting control

AT+CRC Set Cellular Result Codes for incoming call indication

AT+CREG Network registration

AT+CRLP Select radio link protocol param. for orig. non-transparent data call

AT+CRSM Restricted SIM access

AT+CSCS Set TE character set

AT+CSNS Single Numbering Scheme

AT+CSQ Signal quality

AT+CSSN Supplementary service notifications

AT+CUSD Unstructured supplementary service data

AT+VTD=<n> Tone duration

AT+VTS DTMF and tone generation (<Tone> in {0-9, *, #, A, B, C, D})

AT+WS46 Select wireless network

AT commands originating from GSM 07.05 for SMS

Revision history

document

3 Feature migration

3.2 Certification and standards

Hardware migration

Table 4-1: Operating modes

TC35i/TC35

Table 4-3: Power supply signals

scenarios

Battery pack

RTC backup

Interfaces

Audio Interface

Electrostatic discharge

4.10 Mounting and installation

4.11 Terms and Abbreviations

AT-commands

Table 5-2: AT commands for FAX

Table 5-3: AT commands from GSM 07.07

Table 5-4: AT commands for SMS

functions

Table 5-6: AT commands for SAT

misc

Siemens TC35 Terminal User Manual

Product

Learn More

Legal


Contents Safety information Table Of Contents Table Of Contents Overview Product description Highlights Features External interfaces Installation Interface description Handset connector Antenna connector FME (male) RS232 interface Startup Operating states / LED POWER DOWN Network search AT command control SW update Compatibility Certification / maintenance Index	sUser GuideTC35 Terminalwww.siemens.com/wm be inspired WirelessModuleswww.siemens.com/wm Next / 39