Siemens SIPLUS ION ANALOGINPUT T001 Operating Instructions Manual

Also see for 6AT8000-1BA00-0XA0: Manual

ION ANALOGINPUT T001A5E02189572/A2, 02/2009, © SIEMENS AG 2008, 2009 Ⓟ 2009SIPLUS CMSIndustrial I/O-NodeION ANALOGINPUT T0016AT8000-1BA00-0XA0Operating Instructions (Compact)Contact InformationSIEMENS AGI IA SE DEWürzburger Str 12190766 FÜRTHGERMANYCustomer Support+49 (0) 180 5050 222(€ 0.14 /min. from the Germanlandline network, deviating mobilecommunications prices are possible)Internetwww.siemens.com/siplus-cmsION ANALOGINPUT T001 SIEMENS AGIndustry SectorPostfach 484890026 NÜRNBERGGERMANYScope of delivery● ION ANALOGINPUT T001● Operating Manual (compact)DescriptionThe ION ANALOGINPUT T001 is used to acquire analog signalsand to transmit the recorded data via the FireWire bus (IEEE1394a-standard) with 400 Mbps to a higher level industrial PC. The use ofan ION ANALOGINPUT T001 allows recording 8 analog, separateelectrically insulated signals within a range of ± 10 V.The maximum sample frequency is 40 kHz per analog input.AssemblingThe device must be mounted on a DIN rail. To avoid overheatingthe minimum distances specified in the technical data must beadhered to. Protective equipment and a disconnection unit for thedevice must be provided.ConnectingFor clamping ranges: see technical data.● Screw clamps: Screwdriver with a blade of 3 mm.Recommended fastening torque: 0.2 ... 0.4 Nm.● Ground Connection: TX 15 Torx screwdriver.Recommended tightening torque: approx. 3 Nm.Commissioning (hardware)1. Connect the ION with a 24 V power supply. The green PWRLED of the ION starts to blink.2. Connect the ION with the PC via an IEEE1394 cable.3. If the ION is being connected to the PC for the first time,Windows will request a driver installation. To install the driver,follow the instructions of the hardware assistant. The directoryfor the drive installation is SIPLUS CMS\Drivers\IEEE1394.4. After Windows has installed a driver for the ION, the ION canbe used with X-Tools. The yellow LNK LED of the ION lights upand the hardware installation is complete when the ION isconnected to the PC, the driver is installed and X-Tools isstarted.Technical DataInterfacesIEEE1394a P1... P3Number 3Connector type 6-pin connectorTransfer speed 400 MbpsPower Supply 24 V, 0 V, PD (Power Down)Connector type 3-pin connector(Phoenix Contact)Clamping range 0.2 ... 2.5 mm²Input voltage 18 ... 32 V DCPower loss at 24 V DC 24 WCurrent consumption at 24 V DC 1 AAnalog CH 01... CH 08Number 8Connector type 16-pin connector(Phoenix Contact)Transfer speed 0.2 ... 2.5 mm²Input voltage range ± 10 VInput protection ± 60 VInsulation ± 0.4 kVInput resistance R ≥ 1 MΩInput current l < 10 μASample frequency ≤ 40 kHz / analog inputResolution 16 Bit (15+1)Coupling DCGain error 0.025 % ± 1 digitOffset error 0.017 % ± 1 digitStatic offset Max. 0.12 %CMR 100 dBGround ConnectionConnector type M4 screw on the front:SHIELDClamping range Cable socket for screw M4CablesFireWire According to IEEE1394astandardAnalog inputs Maximum length: 3 mEnvironmental Conditions / EMCTransport and storagetemperature- 25 ... + 85 °CAmbient temperature duringoperation0 ... +55 °CHumidity rating 5 ... 95 %, non condensingEMC interference emission EN 55011 (class A)EMC interference immunity EN 61000-6-2:2005Degree of protection IP20Constructive layoutDimensions (H x W x D) in mm 200 x 60.2 x 126.5Minimum distances:FrontTopBottom80 mm25 mm25 mmDesign Aluminum / stainless steelColor SilverWeight 1 kgMounting DIN railEN 50022-35x15thickness 2.3 mmCertificatesCE For use in industrial and officeareas

/ 2

Related manuals for Siemens 6AT8000-1BA00-0XA0