<span role="presentation" dir="ltr" style="top:97.66%; left:40.89%">ac.maher.co.ir</span>

Siemens SINAMICS DCM Manual

SINAMICS DCM

Technical data

C98130-A7067-A1

Operation

Maintenance

ESD-sensitive components

Ordering information

Rating plates, packaging label

Ordering information for options and accessories

Description

Environmental conditions

Unit data

Transport, unpacking, installation

Installation

Dimension drawings

Dividing the unit

Removal/Installation and division of modules

Firing pulse transformers C98043-A7043

Fuse monitoring equipment C98043-A7118 and voltage measurement equipment C98043-A7117

Installing options and accessories

Connecting

Instructions for EMC-compliant drive installation

EMC-compliant drive installation (installation instructions)

Arranging components for converter units

Information on line-side harmonics produced by converter units in a fully-controlled two pulse bridge circuit configuration (B6C and (B6)A(B6)C)

Data on the line-side harmonics from converter units in a fully-controlled AC bridge circuit B2C

Cable routing in the unit

Block diagram with connection suggestion

Connecting the external power unit

Division options

Measurement of the armature current

Current measurement with two current transformers on the line side

Current measurement via terminal block XB-1 to XB-4 with external measuring circuit

Differential input for +/-10 V at rated armature DC current

External current measurement via X21A or X_I_IST

Offset correction via XN1

Connecting the firing pulse transformers

Parallel connection of firing pulses

Connecting voltage measurement equipment

Connecting fuse monitoring equipment

Parallel connection of power units

Field supply

Line reactors

Fuses

Arrangement of printed circuit boards

Arrangement of customer connections (connector terminals, Faston mounting tabs)

Connector assignment (terminals, Faston mounting tabs, ribbon cables)

Connecting the protective conductor

Open-loop and closed-loop control section

Voltage measurement equipment

Fuse monitoring equipment

Firing pulse transformers

Firing pulse

Ribbon cables

Additional system components

Option Board: Communication Board CBE20

Interface description

Meanings of the LEDs on the Communication Board Ethernet CBE20

technical specifications

safety instructions

Connection examples

DRIVE-CLiQ interface X500

X521/X531 alternative encoder system interface

X524 electronic power supply

Dimension drawing

Electrical connection

Terminal Module TM15

Connection example

X500 and X501 DRIVE-CLiQ interface

X520 digital inputs/outputs

X522 digital inputs/outputs

Terminal Module TM31

X520, X530 digital inputs

X540 auxiliary voltage for the digital inputs

Analog inputs current/voltage switch

X541 bidirectional digital inputs/outputs

Meanings of the LEDs on the Terminal Module TM31

Safety information

Base Drive panel description

Rated DC current

Expandable functionality using SINAMICS components

Base Drive panel catalog numbers

Service

Option part numbers

CUD Kits

Applicable standards

Installation information

Base Drive panel outlines

Base Drive panel schematics

Control connections control units (CUD)

Control units (CUD)

Description of power / control terminals

Safety notes

Safety and application instructions

Mechanical installation

Electrical installation

Configuring

A.1 Customer Service

A.2 Environment

A.3 Standards, certifications

pulse parallel connection

Instructions

Area of application

Configuration

Power increase with parallel connection

Parallel connection of additional SINAMICS DCM units in 12-pulse operation

Prerequisites for the device

Dimensioning of the converter transformer

Dimensioning of the smoothing reactors

Selection for overvoltage protection

Insulation monitoring

Specifying the operating mode

Additional parameter settings

Carrying out commissioning

Optimization for 2 individual reactors

Optimization for an interphase transformer

pulse series connection

pulse series connection: controlled converter + uncontrolled converter

Voltage limits

Optimization runs

Switchover of the power unit topology - option S50

Index

Compact User Manual, 09/2016, A5E34871844AM

safety STO, SS1 (ISO

Introduction

Safe Torque Off (STO)

Recommended safety relays

Recommended circuit

Field circuit description

Safety shutdown (E-STOP)

Parameterizing the digital outputs

Parameterizing the digital input for SS1 OFF3

Abbreviations and circuit diagram symbols

Principle of the dual channel architecture

STO stop Category 0 with one switching device

STO circuit example with one 3WL circuit breaker

STO circuit example with one power contactor

SS1 stop Category 1 with one switching device

SS1 circuit example with one 3WL circuit breaker

SS1 circuit example with one power contactor

STO, two switching devices in series

STO circuit example with two 3WL circuit breakers connected in series

STO circuit example with two power contactors connected in series

SS1, two switching devices connected in series

SS1 circuit example with two 3WL circuit breakers connected in series

SS1 circuit example with two power contactors connected in series

STO stop Category 0, several power units

STO circuit example with two power units and circuit breakers

STO circuit example with two power units and power contactors

SS1 stop Category 1 for several power units

SS1 circuit example with two power units and circuit breakers

Evaluating the safety functions according to EN ISO 13849 when using one switching device

Evaluation of "Detect

Evaluation of "Evaluate

Evaluation of "Respond

Evaluation of a power contactor

Result when using a 3WL circuit breaker

Evaluating the safety functions according to EN ISO 13849 when using two switching devices

Evaluation of two power contactors connected in series

Result of "Respond" with two 3WL circuit breakers

Result when using two power contactors

Evaluation of the safety function according to EN 62061

Evaluation of two power contactors

Result "Respond" when using two power contactors

Standards

Connection circuit diagrams for the switching devices

Recommended circuit breakers and power contactors

Function diagrams

technical support

Fundamental safety

Parameters

Industrial security

Overview of parameters

Faults and alarms

Number ranges of parameters

List of parameters

Parameters for data sets

Parameters for drive data sets (DDS)

Parameters for encoder data sets (EDS)

Parameters for write protection and know-how protection

Parameters with "KHP_WRITE_NO_LOCK

Parameters with "KHP_ACTIVE_READ

Explanations on the function diagrams

Overviews

CUD input/output terminals

Control Unit communication

PROFIdrive

Internal control/status words

Sequence control

Brake control

Setpoint channel

Encoder evaluation

Armature circuit control

Field circuit control

Power unit

Technology controller

Signals and monitoring functions

Siemens SINAMICS DCM Manual

Product

Learn More

Legal