Edition 05/2020Installation ManualSIMATIC NETRugged Multi Service PlatformsRUGGEDCOM RX1501https://www.siemens.com

Siemens RUGGEDCOM RX1501 Installation Manual

open source

how this guide is organized

customer support

Introduction

NETCONF Capabilities and Namespaces

NETCONF Sessions

Getting Data

Examples

Sample Session: Performing an Action

Sample Session: Editing Data

Vendor-Defined Capabilities

Vendor-Defined Namespaces

Viewing the Capabilities on a Device

Saying Hello

RUGGEDCOM ROX II NETCONF <hello> Message

Closing the Session

Using the <get-config> Command

Using XPaths with <get> and <get-config

Getting Information for a Specific Object

Specifying Objects with XPaths

Getting Data Models from the Device

Getting Schemas from the Device

Getting YIN and YANG Files from the Device

Using pyang

Using the Text-Based Tree

Changing Configuration Data

Changing Data in the Candidate Configuration

Locking Data Stores

Copying Data

Replacing Data

Deleting Data

Validating Changes

Committing Changes

RUGGEDCOM ROX II Actions

Admin Namespace Actions

snmp-discover

decline-upgrade

roxflash

shutdown

restore-factory-defaults

backup-files (Backup Files)

full-configuration-load

reset (Modem)

reset (Cellular Modem)

reset (Serial Port)

restart-serserver

clear-port-stats (Switch Port)

clear-cable-stats-port (Switch Port)

log (Link-Failover)

cancel-test (Link Failover)

clear-stp-stats (Switch)

clear-all-switch-stats (Switch)

display-public-key (IPSEC)

install-ca-certificate (IPSEC)

install-crl-file (IPSEC)

remove-ca-certificate (IPSEC)

remove-crl (IPSEC)

Getting the System Name

Getting the Chassis Status

Clearing All Alarms

Changing the System Name by Locking and Committing

Changing the System Name Directly

Creating a Static VLAN

Assigning a PVID on a Port

Disabling Spanning Tree on a Specific Port

Configuring an IP Address on a Specific Port

Deleting an IP Address

Setting a Static Route

Disabling Spanning Tree Globally

Retrieving all IP Addresses from the Running Configuration

Configuring Static Multicast Routing on a Layer 3 Device

Enabling Static Multicast Routing on a Layer 3 Device

Retrieving Static Multicast Status on a Layer 3 Device

Replacing an IP Address

Configuring a Port to Dynamically Obtain an IP Address

Configuring OSPF Area and Network on a Layer 3 Device

Enabling the OSPF Passive-Default Option

Configure an OSPF Non-Passive Port

Configuring OSPF Parameters

Enabling the OSPF redistribute-connected Option

Enabling OSPF on a Layer 3 Device

Retrieving OSPF Status

Retrieving All Data from the Routing Namespace

Configure the DHCP Server Port Listening for DHCP Client Requests

Enabling the DHCP Server Service

Disabling an Ethernet Port

Enabling an Ethernet Port

Checking an IP Address on a Specific Port using the Interfaces Namespace

Retreiving All Data From Running Database Including Default Values

Changing a User's Password

RUGGEDCOM RX1500

security information

system requirements

Feature Keys

Troubleshooting

Available Services by Port

User Permissions

Using ROX II

Connecting Through the Network

Default Usernames and Passwords

Logging Out

Navigating the Interface

view mode

Edit Toolbar

Icons

Common Controls

Using Network Utilities

Dumping Raw Data to a Terminal or File

Tracing the Route to a Remote Host

Pinging an IPv4 Address Using MPLS Protocols

Using the Command Line Interface

Device Management

Determining the Product Version

Viewing Module Information

Viewing Flash Card Storage Utilization

Viewing the Slot Status

Viewing the Slot Sensor Status

Viewing the Parts List

Shutting Down the Device

Restoring Factory Defaults

Decommissioning the Device

Managing Files

Downloading Files

Viewing Logs

Deleting Logs

Managing Diagnostic Logs

Enabling/Disabling the Developer's Log

Enabling/Disabling the NETCONF Summary Log

Enabling/Disabling the NETCONF Trace Log

Enabling/Disabling the XPATH Trace Log

Enabling/Disabling the WebUI Trace Log

Viewing a List of Remote Servers

Deleting a Remote Server

Managing Remote Server Selectors

Deleting a Remote Server Selector

Managing the Software Configuration

Loading a Configuration

Upgrading/Downgrading the ROX II Software

Configuring the Upgrade Source

Adding Software Releases to the Upgrade Server

Using Microsoft IIS Manager 6.0 or Higher as an Upgrade Server

Stopping/Declining a Software Upgrade

Rolling Back a Software Upgrade

Managing ROX II Applications

Viewing a List of Installed Applications

Upgrading an Application

Uninstalling an Application

Managing Application Repositories

Checking the Repository Connection

Adding a Repository

Deleting a Repository

Managing Feature Keys

Installing Files

Backing Up Files

Managing Fixed Modules

Deleting a Fixed Module Configuration

Installing a New Line Module

Viewing a List of Line Module Configurations

Enabling/Disabling Controlled Bypass for M12 Line Modules

Managing Event Trackers

Viewing a List of Event Trackers

Adding an Event Tracker

Deleting an Event Tracker

Security Recommendations

Removable Memory

Using RUGGEDCOM ROX II

Logging In

Tracing the Route of an IPv4 Address Using MPLS Protocols

Using Command Line Completion

Editing Commands

Using Output Redirects

Using Regular Expressions

Using CLI Utilities

Common Commands

File Commands

Interface and Services Commands

Administration Commands

Configuration Mode General Commands

Configuring the CLI Interface

Accessing BIST Mode

Accessing Service Mode

Accessing Maintenance Mode

device management

Viewing the Slot Hardware

Viewing CPU/RAM Utilization

Viewing the Power Controller Status

Rebooting the Device

Managing Logs

Configuring Secure Remote Syslog

Viewing a List of Permitted Peers

Managing Remote Syslog Servers

Viewing a List of Remote Server Selectors

Upgrading/Downgrading the RUGGEDCOM ROX II Software

Setting Up an Upgrade Server

Downgrading Using ROXflash

Managing RUGGEDCOM ROX II Applications

Installing an Application

Siemens RUGGEDCOM RX1501 Installation Manual

Product

Learn More

Legal