![Sharp SPC729 Instruction Manual & Warranty Manual pdf 1 page image](https://manuals-archive2.s3.amazonaws.com/5614598/4cd171130d147d9837452ac63f43583e1f.jpg)
Sharp SPC729 Instruction Manual & Warranty
![]()
SPC729 Bluetooth Alarm Clock Radio with USB PortInstruction Manual & WarrantyThank you for your purchase of this quality clock. The utmost care has gone into the design andmanufacture of your clock. Please read these instructions and store them in a safe place for futurereference.1. PM indicator2. Alarm 1 indicator3. Bluetooth indicator4. Alarm 2 indicator5. FM indicator6. /FM/OFF button7. ALARM 1 button8. TUNING < buttonCONNECTING TO THE POWER SUPPLYBegin by plugging in the AC adapter into a standard household outlet and the other end of the cord intothe DC 5V jack at the back of the unit.INSTALLING THE CLOCK & ALARM BACK UP BATTERIESThe clock time and alarm (if set) can be maintained during a power failure by 2 x AAA/ LR03 batteries (notsupplied). Once the power is restored, check the time to make sure it is accurate and re-set if necessary.INSERTING THE BATTERIES1. Open the battery compartment at the back of the unit by pressing on the catch and removing the cover.2. Insert 2 x AAA/ LR03 batteries (preferably alkaline batteries) into the battery compartment, followingthe polarity as shown on the diagram inside the compartment.3. Replace the battery compartment cover.USB CHARGINGTo charge, connect your USB device to the USB port of this clock.Note:1. Use only with devices that require 5V USB power.2. Each USB port provides 2,000mA recharging current. Devices requiring more than 2,000mA should notbe used.3. Charging time may vary for different devices.SETTING THE CLOCK1. While the radio is off, press and hold the TIME SET button to activate time setting.2. While holding down the TIME SET button, press the HOUR button to advance to the correct hour. ThePM indicator will light when the hour is advanced into the PM time..4. Release the TIME SET button when the correct time is shown on the displaySETTING THE ALARM1. To set the alarm time, follow steps (1) to (4) above, using ALARM1/2 button, instead of the TIME SETbuttonUSING THE ALARM FUNCTION1. Press the ALARM 1/2 button to select wake to beep or radio, and the selected alarm mode will lightup.2. The beep or radio will come on at the set time.3. To stop the alarm, press /FM/OFF or ALARM 1/2 button and the alarm will sound again the next day.4. To turn the alarm off completely, press the ALARM 1/2 button until the alarm indicator hasdisappeared from front display.Note: While the beep alarm volume is fixed and cannot be adjusted, the radio alarm volume can beadjusted to your desired level using the VOLUME buttons. To select a radio station to wake up to, seethe section on “LISTENING TO THE RADIO”.SNOOZE FUNCTIONPressing the SNOOZE button after the alarm sounds will cause the alarm to pause and the alarm willsound again in 9 minutes. This will happen each time the SNOOZE button is pressed.SLEEP FUNCTIONWith this function, you can listen to the radio for up to 60 minutes, after which it will turn off automatically.1. When the radio is turned on, press the SLEEP button repeatedly to select the duration: 60, 45, 30, 15,05 minutes or OFF.2. At the end of the set time, the radio turns off automatically.3. To cancel the sleep function before the end of the set time, press the /FM/OFF button to turn offthe radio immediately.LISTENING TO THE RADIO1. Press the /FM/OFF button to select the FM mode.2. Press and hold the |
This manual is suitable for:
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved