Sharp DV-RW360H Operation Manual

33ENRecording Disc Playback EditingBefore you start Connections Getting startedChanging theSetup menu OthersVCR functionsRecordingTimer Recording (cont’d)1 2 3654708 9MENU LISTTOP MENUSTOPPLAYFWDREVSKIPPROG.CLEAR/C-RESETVCRREC/OTR DVDREC/OTRPQRS TUV WXYZGHI JKL MNO.@/: ABC DEFSPACE DISPLAYENTERZOOMREC MODEVCRRAPID PLAYDVD CM SKIPSETUPT-SETOPEN/CLOSEEJECTTIMER PROG.DUBBINGRETURNOPERATEIn the following example, No.5 timer programming overlapson No. 1 and No. 6 timerprogrammes. In such a case, youshould correct the programmetime to clear the overlap.Timer Programming2. - - -3. - - -4. - - -7. - - -8. - - -OverlapNo.1 65. 01/01 12:30 14:00 P02 DVD SP1. 01/01 12:00 13:00 P01 DVD XP6. 01/01 13:45 21:00 P12 DVD SEPDate Start End CH ModeDVDVCRDVDVCR1Press [T-SET] so that theicon disappears from the frontpanel display.2Press [TIMER PROG.].Timer Programming list willappear.Timer Programming2. - - -3. - - -4. - - -5. - - -6. - - -7. - - -8. - - -1. 01/01 12:00 13:00 P01 DVD XPDate Start End CH ModeDVDVCRDVDVCR3Check the information on thelist you will need.4To clear the timer program-ming, select the desired pro-gramme using [Cursor K / L],then press [CLEAR/C-RESET].To correct the timer program-ming1) Select the desired programmeusing [Cursor K / L], thenpress [ENTER].2) Correct the timer programmingusing [Cursor K / L / { / B].3) Press [ENTER] again.5Press [TIMER PROG.] to exit.6Press [T-SET] to return to thetimer-standby mode.To check the timer program-ming in processPress [TIMER PROG.].61Note• If a timer recording isproceeding, that programmeis highlighted in red. In sucha case, you cannot select anyother programmes.• When you check the timerprogramming in progressby pressing [TIMER PROG.]during operations of thecomponent (VCR or DVD)which is not currently usedfor the timer recording,the programme will not behighlighted. In this case,you cannot select otherprogrammings.Checking, cancelling, or correcting the timerprogramming informationTo stop the timer recording in progressPress [STOP C] to stop the disc recording or [STOP C/EJECT A] tostop the tape recording on the front panel of the unit.Note• [STOP C] on the remotecontrol is not effective.The error numbers indicate:If the timer programming did not complete correctlyThe error number appears on theTimer Programming list.Timer Programming2. - - -3. - - -* 01/01 12:00 13:00 P01 DVD E1Date Start End CH ModeDVDVCRDVDVCRThe error programme will bedisplayed in grey with an asteriskand have an error number.The error programme will bedeleted once you check the errorin the programme list, or onceyou cancel the timer-standbymode and re-enter it.Press [CLEAR/C-RESET] to erasethe selected programme.E1-22E37-39Recording errorE23-24 Unrecordable discE25 • Copy prohibited programme• Cannot record because of theNTSC / PAL-60 signal is received.E26-28 Copy prohibited programmeE29 Disc protectedE30 Disc fullE31 Already recorded 99 titles (Videomode)E32 Already recorded 99 titles (VRmode)E33 Already recorded 999 chaptersE34 No space for Control informationE35 PCA (Power Calibration Area) fullE36 Already finalised Video format discE40 • There are some unrecordedparts due the overlapped timerprogrammes.• Recording did not start at thestart time.• There is no tape in the cassettecompartment.• Tape recording reaches tothe tape end during timerrecording.E41 Power failureE42 No disc2564Downloaded from: http://www.usersmanualguide.com/