Sharp AR-FX7 Service Manual

Also see for AR-FX7: Operation manual Operation manual

AR-FX7 SOFT SWITCH 7 - 32SW31 No.3–No.8 Time specification print (min) on thecommunication report tableUsed to set "min" of the time (o’clock, min) when specifying the time onthe communication report table.Setup is in the range of 0 – 59 (min) by binary input.(When set to 60 – 63, the time is set to 0min.)Default: 0 minSW32 No.1, No.2 Default telephone book setupUsed to set YES/NO of default telephone book displaying.Default: 0 0 (Basic screen)SW32 No. 3 Next address key input in broadcastUsed to set YES/NO of Next address key input in broadcast.Default: 0 (No)SW32 No.4, No.5 One-touch dial display number switchUsed to set the number of one-touch dial display.Default: 0 1 (8)SW32 No. 6 Shift of the power OFF state in shut offUsed to set whether the shift of the power OFF state in shut off isallowed or inhibited.Default: 1 (allowed)SW32 No. 7 Time indication formatUsed to set the sequence of year, month, and day in the LCD display,report, and sender record.When set to 1, time is indicated in AM/PM format.When set to 0, time is indicated in 24H format.Default: 0 (24H)SW32 No. 8 Priority in the day of weekUsed to set the recording sequence of the day of month and the day ofweek if the date is in the sequence of month, day, and year.Default: 0 (No) (U.K.) 1 (Yes) (Germany, France)SW33 No. 1 Inhibited to use.SW33 No. 2 Report output on less than A4 (LTR)Used to set the report output on less than A4 (LTR).Default: 0 (Reduction by the record volume)SW33 No. 3 Own FAX No. mark of TX imageUsed to set own number’s mark in TX image header. (English only)When set to 1, mark is TEL icon ( ).When set to 0, mark is “FAX:”.Default: 0 (FAX:)SW33 No.4, No.5 Contents of send document are printedin memory sendUsed to set Print/Not print part of the sent document in the transmis-sion result table in case of a memory transmission error.When set to 0 0, the transmitted document is not printed on the trans-mission result table.When set to 0 1, all the transmitted document are printed on the trans-mission result table.When set to 1 0, the transmitted document is printed on the transmis-sion result table only when the transmission is failed.Default: 1 0 (when the transmission is failed)SW33 No. 6 Transmission document content print in Fcode transmissionUsed to set whether the sent document content is print or not in F codetransmission.SW33-4 – 5 must be set to output.Default: 1 (Not print)SW33 No. 7 Function to attach images to the report tableof memory confidential sendUsed to set whether images are attached to the report table of memoryconfidential sendDefault: 0 (NO)SW33 No. 8 Total communication time and total number ofpages print on communication record tableUsed to set Print/Not print the total communication time and the totalnumber of pages on the communication record table.When set to 1, the total communication time and the total number ofpages are printed on the communication record table.When set to 0, not printed on the communication record table.Default: 1 (YES)SW34 No.1, No.2 Report output (in reception)Used to set whether the communication report table is outputted or notwhen a reception (excluding confidential reception) is made.Setup is selected from "print inhibition," "all output," and "only whentransmission is failed" as follows:Default: 0 0 (printing is inhibited)SW34 No.3, No.4 Report output (in transmission)Used to set whether the communication report table is outputted or notafter the transmission (excluding broadcast, sequential send request,and relay broadcast).Setup is selected from "print inhibition," "all output," and "only whentransmission is failed" as follows:Default: 1 0 (Only when transmission is failed)SW34 No. 5 Communication report output (in confidentialreception)Used to set whether the communication report table is outputted or notwhen a confidential reception is made.When set to 1, the communication report table is printed.When set to 0, the communication report table is not printed.Default: 1 (Print)SW34 No.6, No.7 Report output (In broadcast, sequentialsend request, and relay broadcast)Used to set whether the communication report table is outputted or notafter the transmission (in broadcast, sequential send request, andrelay broadcast).Setup is selected from "print inhibition," "all output," and "only theaddress to which transmission is failed" as follows:Default: 0 1 (All print)SW34 No. 8 Report output when cancelingUsed to set whether the communication report table is outputted or notwhen canceling transmission during document transmission.When set to 1, the communication report table is printed.When set to 0, the communication report table is not printed.Default: 0 (No print)bit 1 20 0 : Print is inhibited.0 1 : Print all1 0 : Only in case of an errorbit 3 40 0 : Print is inhibited.0 1 : Print all1 0 : Only when transmission is failedbit 6 70 0 : Print is inhibited.0 1 : Print all1 0 : Only the address to which transmission is failed