Sealey WL483D Instructions Manual

instructions forbench mounted worklightmodel no: wl483dthank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFetY1.1. electricAl SAFetY wArning! it is the user’s responsibility to check the following:check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs andall electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electricalproducts. You may obtain an rcd by contacting your local sealey stockist.if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (PortableAppliance test) tested.electrical safety information, it is important that the following information is read and understood.1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.1.1.3. imPortAnt: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with thecorrect fuse - see fuse rating in these instructions.8 do not pull or carry the appliance by the power cable.8 do not pull the plug from the socket by the cable.8 do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is8 replaced immediately by a qualified electrician.1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.if the cable or plug is damaged during use, switch the electricity supply and remove from use.Ensure that repairs are carried out by a qualified electrician.Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.b) Connect the BROWN live wire to the live terminal ‘L’.c) Connect the BLUE neutral wire to the neutral terminal ‘N’.ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.Sealey recommend that repairs are carried out by a qualified electrician.2. i introductionPowerful 3 diopter 120mm precision lens gives high quality magnifying capabilities. features 48 smd leds to illuminate the object for improveddetailed work. multi-position swing arm allows simple positioning of lamp to suit task. features a G-clamp base to secure to a workbench ortable. Ideal for electrical engineers, engravers and fine detail work.3. iSPeciFicAtionmodel no:................................................................ wl483dleds: ........................................................................ 48 smdsupply: ...........................................................................230V4. oPerAtion4.1. mounting4.1.1. Fix the clamp to a secure surface. See fig.1.4.1.2. lower the work light assembly into the clamp, use twohands to prevent the lamp moving during this operation.4.1.3. Turn on/off using the switch on top. See fig.2.4.1.4. Adjust by loosening/tightening the head clamp. See fig.3.note: Be aware of the effect of using the lamp closeto a window/door where it could be in direct sunlight.remember to close the lid on top whilst it is not in use.fig.2fig.1WL483D Issue 2 (H,F) 11/01/18Original Language Version© Jack sealey limitedrefer toinstructionmanualrecommended fuse rating3 AmP

/ 2

Related manuals for Sealey WL483D