Menu
Sealey VS913 Instructions Manual
  |
THERMAL IMAGING CAMERAMODEL NO: VS913Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.VS913 Issue 1 09/04/20Original Language Version© Jack Sealey LimitedRefertoinstructions1. SAFETY WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using thisequipment.9 Familiarise yourself with the applications, limitations, and potential hazards of the Thermal Camera.9 Keep the Thermal Camera clean and in good condition.9 Protect the Thermal Camera from the following:- Thermal shock caused by large and/or rapid ambient temperature change.- High temperatures.8 DO NOT get the Thermal Camera wet or use in damp or wet locations or areas where there is condensation.8 DO NOT use the Thermal Camera for any purpose other than that for which it is designed.8 DO NOT allow untrained persons (particularly children) to operate the Thermal Camera.8 DO NOT operate the Thermal Camera when you are tired or under the influence of alcohol, drugs or intoxicating medication.8 WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions andsituations that may occur. It must be understood that common sense and caution are factors which cannot be built into thisproduct, but must be applied by the operator. I2. INTRODUCTIONThermal imaging camera for the detection of high and low temperature. Heat-mapped colour palettes and temperature reading.Includes on-screen cursor to accurately locate minimum/maximum temperature variation. Suitable for many industries includingautomotive, building and electrical.3. SPECIFICATIONModel no.: .................................................................. VS913Colour Palette ...................................................................... 3Emissivity .............................................................. On ScreenField of Vision .......................................................... 33o x 33oImage Mix (Camera to Thermal) ............................... ThermalMemory Capacity ................................4Mb SD Memory CardPower Source .................................... 4 x AAA (Not Included)Resolution ........................................................ 32 x 32 pixelsScreen Size ....................................... 1.8” 128 x 160mm TFTTemperature Range .................................... -20o C to +650o C4. OPERATION4.1. BATTERY INSTALLATION4.1.1. Use a small cross-head screwdriver to remove the battery cover (fig.1).4.1.2. Fit 4 AAA batteries (not supplied) and replace cover (DO NOT over tighten).4.1.3. Press and hold the On/Off button (fig.1) for 2-3 seconds until the start screen appears.4.2. HOME SCREEN DISPLAY (fig.2)4.2.1. Press the “OK” button (fig.3.6) to display the settings menu. Using the Ʌ or V buttons (fig.3.8)highlight the field you wish to set/adjust and press “OK”.4.2.2. Once you have the selected the options to suit your usage, use the return button (fig.3.7) tostart using the unit. Options are:SD Card: View images taken or format SD cardColour: Three variations to choose from.Emissivity: Five settings (.95, .90, .80, .60, .30) See chart (fig.4) overleaf.Temperature units: Celsius or Fahrenheit.Date/Time: 12 or 24 hour clock.Auto Off: Off, 1, 2, 5, and 10 minute settings.fig.1fig.2Hot surfaces |
Related manuals for Sealey VS913
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved