Menu
Sealey VS8200 Instructions Manual
  |
Suitable for internal inspection of modern small diesel engines where access to the cylindercan be quickly made through the aperture left by removal of the glow plug. Inspection of thistype can avoid costly and unnecessary dismantling of the cylinder head. Features anobedient probe with an illuminated camera head diameter of just 4.5mm – suitable for most smallengine applications. Rugged hand-set with IP64 dust/water rating includes controls for the LED probelighting and camera zoom. Live images from the camera head are displayed on a crystal clear screenand may be viewed/saved externally using the AV cable supplied.Optional Ø3.9mm probes in either forward view or side view configuration are available.Uses 4 x AA batteries (supplied).7 DO NOT use the bore scope if dropped and/or damaged7 DO NOT operate near live electrical wires.7 DO NOT operate near moving parts such as pulleys, motors, gears or fans etc.7 DO NOT bend the bore scope shaft tighter than 13cm diameter.7 DO NOT expose the bore scope housing to water or other liquids.7 DO NOT insert the bore scope shaft into locations whose temperature is greater than 55°C. Maintain the bore scope in good and clean condition for best and safest performance. A full range of personal safety equipment is available from your Sealey dealer. Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair. Account for all tools and parts being used and do not leave any in, or near, the engine. Be alert to your surrounding environment while using the bore scope.Note the location of the object to be inspected and determine a route to it. Bend thebore scope shaft to follow the route.Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT ISINTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THEWARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY INSTRUCTIONSINSTRUCTIONS FOR:VIDEO BORE SCOPE 4.5mmMODEL No: VS82002. INTRODUCTION3. SPECIFICATIONShaft Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .900mmMinimum Bend Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13cmProbe Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5 x 1100mmScreen Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 x 56mmResolution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .320 x 240 pixelsBatteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 x AAAccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mirrors - 70°, 90°, 110°. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Magnetic pick up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .HookOptional Probe (3.9 x 800mm) . . . . . . . . . . . . . . . . . . . . . . . . . . .VSBSP39FOptional Probe (3.9 x 800mm) Side View . . . . . . . . . . . . . . . . . .VSBSP39S4. PREPARATION4.1 Batteries4.1.1 Turn the bore scope over and lift up the ring screw (fig.2A) turn the ringanti-clockwise until fully unscrewed and pull to lift open the battery door (fig.2B).4.1.2 Insert AA batteries ensuring correct polarity (fig.2C).4.1.3 Close the battery door screw in the ring screw clockwise until tight and push downout of the way (fig.2D).4.2 Probe4.2.1 Pull back the threaded sleeve on the end of the probe and ensure the red doton the tab is facing upwards (fig.3A), take the probe and insert it into the top ofthe bore scope housing.The probe will only connect one way.4.2.2 With the probe pushed firmly in, screw the sleeve onto the housing to secureit in place (fig.3B).4.3 Probe Attachments4.3.1 There are five attachment for this bore scope, a hook, a magnet and 3 angledmirrors (fig.4).4.3.2 Each attachment is connected the same way - by screwing onto the threadedend of the probe.fig.1fig.2fig.4Original Language Version VS8200 Issue: 1 - 08/03/11fig.3 |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved