Menu
Sealey SPP01 Instructions Manual
Also see for SPP01: Instructions
  |
instructions forSOLAR PANELSmodel no: SPP01 12V/1.5W, SPP03 12V 4.8WThank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY9 observe standard safety procedures when using the ssP01.▲ DANGER! - Beware, lead-acid batteries generate explosivegases during normal battery operation.9 if the battery terminals are corroded or dirty, clean them beforeattaching the clips.9 Remove ill fitting clothing. Remove ties, watches, rings andother loose jewellery. contain, or tie back, long hair whenworking near batteries.9 Keep children and unauthorised persons away from connections. WARNING! DO NOT use solar panels on any vehicles other thanthose with12Volt dc systems.8 DO NOT dis-assemble solar panel. the solar panel must bechecked by qualified service personnel only .8 DO NOT get solar panel wet or use in damp locations or areaswhere there is condensation.8 DO NOT use the solar panel for any purpose other than for whichit is designed.8 DO NOT pull the cables or clips from the battery terminals.8 DO NOT operate the solar panel if damaged.9 When not in use store in a safe, dry, childproof location.2. INTRODucTIONAmorphous solar panels convert daylight directly into 12V electricity. suitable for maintaining charge in a wide range of batteries and powerpacks. ideal for batteries stored in boats and caravans and for batteries in vehicles in long term storage. Advanced technology solar panelsrequire only daylight to generate power. supplied with battery clips and vehicle accessory plug.3. SPEcIFIcATIONmodel no: .................................................................... sPP01output: ................................................................... 12V/1.5Wdimensions: ......................................................340 x 120mmmodel no: .................................................................... sPP03output: ................................................................... 12V/4.8Wdimensions: ......................................................410 x 345mm4. OPERATION4.1. Installation.4.1.1. Insert the suction cups (SPPO1 only) into the pre-drilled ends of the solar panel ensuring that they are securely fixed.choose a clean, dry surface, facing the sun, then dampen suction cups and mount to vehicle’s dash or windscreen.4.2. connection through vehicle accessory socket4.2.1. Attach the auxiliary adaptor lead to the solar panel lead. Plug the male-end of the auxiliary adaptor (12V plug) into the female auxiliarysocket (in the vehicle) making sure that both ends are secure and aligned correctly. for optimal charging power, ensure the panel(solar cell up) is directly facing the sun.4.3. Battery connection.note: check the battery is 12Vdc. DO NOT use with a 24V battery.4.3.1. Attach the battery clip lead to the solar panel lead.4.3.2. ensure the battery terminals are clean, if necessary clean away any corrosion.4.3.3. clip the red (+) crocodile clip to the red (+) terminal post on the battery.4.3.4. clip the black (-) crocodile clip to the black (-) terminal post on the battery. WARNING: When disconnecting remove the black (-) clip from the battery first then remove the red (+) clip.sPP01, sPP03 | issue:3(l) 22/08/17Original Language Version© Jack sealey limitedrefer toinstructionmanualconnect to any 12V auxiliarypower outletconnect directly to batteryusing Dc cables |
Related manuals for Sealey SPP01
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved