Sealey SM355B Instructions Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONS1.2. GENERAL SAFETY WARNING! Disconnect the cut-off machine from the mains power, and ensure that the cutting blade is at a complete standstill beforeattempting to change accessories, service or perform any maintenance. Maintain the cut-off machine in good condition (use an authorised service agent). Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty. Locate the cut-off machine in a suitable work area. Ensure that the surface is flat and firm. Keep the area clean and tidy and free fromunrelated materials, and ensure that there is adequate lighting. Keep the cut-off machine clean for best and safest performance and check moving parts alignment regularly. WARNING! Before each use check that the cutting blade is secure and that it is not worn or damaged.NOTE: Only competant persons should attempt to change cutting blades. Ensure that replacement blades are not damaged in any way - cracks or deformations etc. Also check the mounting flanges to check thatthey are not deformed, burred or chipped. DO NOT over tighten a blade and never tamper with a blade in order to adapt it to a differentsize holder. Always use a blade suitable for the material being cut. Ensure that the cutting blade's specified maximum speed is equal to, or higherthan, that indicated on the machine data plate. Once mounted on the cut-off machine, test the blade before use by facing the cut-offmachine in a safe direction (point blade away from yourself, others and vulnerable items) and running it for a short time. WARNING! Keep guard and holding screws in place, tight and in good working order. Check regularly for damaged parts.A guard or any other part that is damaged must be repaired or replaced before next use. The safety guard is a mandatory fitting whenthe cut-off machine is used on premises covered by the Health & Safety at Work Act. Remove adjusting keys and wrenches from the machine and its vicinity before turning it on.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGEAND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.SM355B Issue: 4(I) 25/02/141.1. ELECTRICAL SAFETY WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets andany other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation ofappropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We alsorecommend that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that areplugged into a supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a ResidualCurrent Device by contacting your Sealey dealer.You must also read and understand the following instructions concerning electrical safety.1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualifiedelectrician, using a Portable Appliance Tester (PAT), at least once a year.1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliancesand the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.and use a Portable Appliance Tester.1.1.4. Ensure that cables are always protected against short circuit and overload.1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connectionsto ensure that none is loose.1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supplyto be used and that the plug is fitted with the correct fuse - see fuse rating at right.1.1.7. DO NOT pull or carry the appliance by the power cable.1.1.8. DO NOT pull the plug from the socket by the cable.1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faultyitem repaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug isdamaged, cut the cable just above the plug and dispose of the plug safely.Fit a new plug according to the following instructions (UK only).a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.b) Connect the BROWN live wire to the live terminal ‘L’.c) Connect the BLUE neutral wire to the neutral terminal ‘N’.d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulationextends beyond the cable restraint and that the restraint is tight.Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.To rewire, connect the wires as indicated above -DO NOT connect either wire to the earth terminal.1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure thata suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with yourelectrician.1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any applianceplugged into it will be protected. The cable core section is important and should be at least 1.5mm2 , but to be absolutely sure that thecapacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the useof 2.5mm2 section cable.Original Language Version© Jack Sealey LimitedRECOMMENDEDFUSE RATING 13AMPINSTRUCTIONS FOR:CUT-OFF MACHINE 355MM 230V WITH BLADEMODEL No: SM355B

/ 4

Related manuals for Sealey SM355B