Menu
Sealey SDSPLUS26 Instruction Manual
    |
26mm SDS PluS RotaRy HammeR DRill900W/230VModel no: SDSPluS26thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.imPoRtaNt: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. Safety1.1. eleCtRiCal Safety WaRNiNG! It is the user’s responsibility to check the following:Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs andall electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electricalproducts. You may obtain an RCd by contacting your local Sealey stockist.If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (PortableAppliance Test) tested.electrical safety information, it is important that the following information is read and understood.1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.1.1.3. important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with thecorrect fuse - see fuse rating in these instructions.8 Do Not pull or carry the appliance by the power cable.8 Do Not pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.8 Do Not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by aqualified electrician.1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.If the cable or plug is damaged during use, switch off the electricity supply and remove from use.Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.Class II products are wired with live (brown) and neutral (blue) only are marked with theClass II symbol;A) Connect the BROWN live wire to the live terminal ‘L’.B) Connect the BLUE neutral wire to the neutral terminal ‘N’.C) After wiring, check that there are no bare wires and ensure that all wires have been correctlyconnected.ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.8 Do Not connect either wire to the earth terminal.Sealey recommend that repairs are carried out by a qualified electrician.1.2. GeNeRal Safety9 disconnect the drill from the mains power before changing accessories, servicing or performing any maintenance.9 Maintain drill in good condition. Check moving parts and alignment and keep drill bits sharp. If necessary use an authorised serviceagent.9 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate thewarranty.9 Wear approved safety eye protection with side shields and a dust mask if drilling generates dust. Protective gloves arerecommended when using out doors and safety gloves when drilling items such as steel, brick work etc, remove ill fitting clothing.Remove ties, watches, rings, other loose jewellery and contain long hair.9 Use drill in an adequate working area for its function, keep area clean, tidy and free from unrelated materials and ensure adequatelighting.9 Evaluate your working area before using the drill i.e. ceiling, floors and enclosures may contain hidden electrical wires or waterpiping.9 Maintain correct balance and footing.8 Do Not over-reach and ensure the floor is not slippery and wear non skid shoes.9 The supplementary handle grip should always be attached for use.9 Keep children and unauthorised persons away from the working area.8 Do Not hold unsecured work in your hand.9 Secure non stable work piece with a clamp, vice or other adequate holding device.9 Avoid unintentional starting and ensure the lock on button is disengaged before use.8 Do Not force the drill to achieve a task it was not designed to perform.8 Do Not operate drill where there are flammable liquids or gasses.8 Do Not get the drill wet or use in damp or wet locations.Recommended fuse rating13 AmpOriginal Language Version© Jack Sealey limitedRefer toinstructionsWear eyeprotectionWear protectiveglovesWear earprotectionWear safetyfootwearWear protectiveclothingSDSPLUS26 Issue 1 24/09/19 |
Related manuals for Sealey SDSPLUS26
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved