Sealey SDA01 Quick Start Manual

Also see for SDA01: Instructions Instructions Instructions

aIR OPERaTED PaNEL DRYERWITH aDJUSTaBLE aIRFLOWmODEL NO: SDa01Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTaNT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SaFETY9 Familiarise yourself with this products application and limitations. WaRNING! Disconnect from the air supply before performing any maintenance.9 maintain the dryer in good condition (use an authorised service agent).9 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.9 Locate the dryer in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and ensurethere is adequate ventilation and lighting.9 Keep the dryer clean for best and safest performance.9 Ensure the air system is suitable to the dryer consumption, (see specifications).9 Wear approved respiratory protection and safety eye goggles.9 Keep children and unauthorised persons away from the working area.9 When not in use ensure the air supply is turned off.9 Avoid unintentional operation.8 DO NOT use the dryer for any purpose other than for which it is designed.8 DO NOT operate dryer if any parts are missing or damaged as this may cause failure or personal injury.8 DO NOT direct air from the air hose at yourself or others.9 When not in use switch the dryer off, and disconnect from the air supply.2. INTRODUcTIONDesigned for drying water based paints. Operates on workshop air supply. Filter prevents airborne particles contaminating paint surface.Adjustable airflow to regulate as required. Ideal for localised or spot repair. May be hand held or mounted on optional Double Support Stand -Model no: SDAST.3. SPEcIFIcaTIONmodel no .....................................................................SDA01Standard set up ........................................................... 1.4mmmax. working pressure .................................................. 90psiAir consumption ........................10cfm@15psi, 20cfm@90psiAir inlet ......................................................................1/4”BSP4. aIR SUPPLY4.1. air Supply4.1.1. Ensure spray dryer air valve is in the “off” position before connecting to the air supply.4.1.2. You will require an air pressure of 90psi, and an air flow according to specification. WaRNING! Ensure the air supply is clean and does not exceed 90 psi while operating the dryer. Too high an air pressure andunclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.4.1.3. Drain the air tank daily. Water in the air line will ruin the paint finish and damage the dryer.4.1.4. Clean air inlet filter weekly. Recommended hook-up procedure is shown in (fig.1).4.1.5. Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.4.2. couplings4.2.1. movement can cause failure if a quick change coupling is connected directly to the dryer when used without optional stand,model No. SDAST. To overcome this, connect a leader hose to the dryer. A quick change coupling may then be used to connect theleader hose to the air line recoil hose. (See fig’s.1 & 2).Refer toinstructionmanualWeareye protection WearprotectiveclothingWeara maskSDA01 | Issue: 3 (H,3,F) 30/08/18Original Language Version© Jack Sealey LimitedFig. 1 Fig. 2

/ 2

Related manuals for Sealey SDA01