Sealey RE023 Instructions Manual
1.1. ELECTRICAL SAFETY WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets andany other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriatesafety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommendthat a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into asupply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device bycontacting your Sealey dealer.You must also read and understand the following instructions concerning electrical safety.1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used onbusiness premises, are tested by a qualified electrician, using a Portable Appliance Tester (PAT),at least once a year.1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for thesafe condition of those appliances and the safety of the appliance operators. If in any doubtabout electrical safety, contact a qualified electrician.1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to thepower supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.1.1.4. Ensure that cables are always protected against short circuit and overload.1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections toensure that none is loose.1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be usedand that the plug is fitted with the correct fuse - see fuse rating at right.1.1.7. DO NOT pull or carry the appliance by the power cable.1.1.8. DO NOT pull the plug from the socket by the cable.1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty itemrepaired or replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged, cut the cable just above the plug anddispose of the plug safely.Fit a new plug according to the following instructions (UK only).a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.b) Connect the BROWN live wire to the live terminal ‘L’.c) Connect the BLUE neutral wire to the neutral terminal ‘N’.d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outerinsulation extends beyond the cable restraint and that the restraint is tight.Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only. Torewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensurethat a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket withyour electrician.1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any applianceplugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that thecapacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of2.5mm² section cable.1.2 GENERAL SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using thisequipment. Familiarise yourself with the application, limitations and potential hazards of the staple gun. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. Locate staple gun in a suitable working area, keep area clean and tidy and free from unrelated materials. Keep the work area clean, uncluttered and ensure there is adequate lighting. Keep the staple gun clean for best and safest performance. Ensure there are no flammable or combustible materials near the work area. Wear approved safety eye protection (standard spectacles are not adequate). Wear heat resistant gloves and appropriate protective clothing.RECOMMENDEDFUSE RATING: 13AMPInSTRUCTIonS FoR:PLASTIC REPAIR HOT STAPLE GUNmoDEL no: RE0231. SAFETYOriginal Language Version© Jack Sealey LimitedIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THEPRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.Wear eyeProtectionWearRespiratoryProtectionWear HeatResistant GlovesHot SurfacesRE023 Issue: 1 - 15/05/14 |
Related manuals for Sealey RE023
This manual is suitable for:
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved