Sealey Power Tools SA623.V2 Instructions Manual

1. safety instructions3 Follow all workshop health & safety rules, regulations, and conditions when using screwdriver.p WarninG! Disconnect from air supply before changing accessories or servicing.3 Maintain screwdriver in good condition and replace any damaged or worn parts. Usegenuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.p WarninG! Check correct air pressure is maintained and not exceeded. We recommended90psi.3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before eachuse and ensure that all connections are secure.3 Wear approved safety eye and ear protection.3 Keep screwdriver bits clean and in good condition for best and safest performance.3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.3 Secure non stable work piece with a clamp, vice or other adequate holding device.3 Ensure the screwdriver bit is secure in the chuck.3 Avoid unintentional starting.3 Keep children and unauthorised persons away from the working area.7 Do not get the screwdriver wet or use in damp or wet locations.7 Do not hold the workpiece by hand. Use clamps or a vice to secure the workpiece.7 Do not use the screwdriver for a task it is not designed to perform.p WarninG! Do not use screwdriver if damaged or faulty. Contact your local service agent.7 Do not use screwdriver unless you have been instructed in its use by a qualified person.7 Do not drop, throw or abuse the screwdriver.7 Do not carry the screwdriver by the air hose, or yank the hose from the air supply.7 Do not operate screwdriver if you are tired, under the influence of alcohol, drugs orintoxicating medication.7 Do not carry screwdriver with your hand on the power trigger in order to avoid unintentionalstarting.7 Do not direct air from the air hose at yourself or others.3 When not in use disconnect from air supply and store in a safe, dry, childproof location.2. introDuction & sPecificationsChuck size . . . . . . . . . . . . . . .6mm HexFree speed . . . . . . . . . . . . . . 11000rpmTorque range . . . . . . . . . . . . . . 175lb.inAir consumption . . . . . . . . . . . . . . 3cfmOperating pressure. . . . . . . . . . . . 90psiAir inlet size . . . . . . . . . . . . . . 1/4” BSPWeight . . . . . . . . . . . . . . . . . . . . . 0.7kgNoise . . . . . . . . . . . . . . . . . . . . .92dB.ACompact design is ideal for accessing workareas where space is limited. Compositelightweight housing reduces effects of chill onoperator’s hands. Fully reversible with thumbcontrol on side of motor housing. Air motor withquality bearings for smooth and powerfuloperation. Features 6mm quick-release chuckfor fast bit changes. Suitable for the professionalworkshop.Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.IMPORTANT: PLease reaD tHese instructions carefuLLy. note tHe safe oPerationaL reQuireMents, WarninGs anD cautions.use tHis ProDuct correctLy anD WitH care for tHe PurPose for WHicH it is intenDeD. faiLure to Do so May causeDaMaGe or PersonaL inJury anD WiLL inVaLiDate tHe Warranty. PLease KeeP instructions safe for future use.INSTRUCTIONS FOR:air PistoL screWDriVerPreMierMODEL No: sa623.V2Original Language Version SA623.V2 Issue: 1 - 17/10/11

/ 3

Related manuals for Sealey Power Tools SA623.V2