Sealey Power Tools SA36.V2 Instructions Manual

Also see for Power Tools SA36.V2: Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICHIT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATETHE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY INSTRUCTIONS3 Follow all workshop Health & Safety rules, regulations and conditions when using this tool.p WARNING! Disconnect from air supply before servicing.3 Maintain tool in good condition and replace any damaged or worn parts. Use genuine parts only.Unauthorised parts may be dangerous and will invalidate the warranty.p WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each useand ensure that all connections are secure.p WARNING! Always wear approved eye and face protection when operating the tool.3 Wear ear defenders and gloves if necessary.3 Keep hands and body clear of the workpiece when operating the tool.3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.3 Secure unstable workpiece with a clamp, vice or other adequate holding device.3 Keep children and non-essential persons away from the work area.7 DO NOT get the tool wet or use in damp or wet locations.7 DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.7 DO NOT use the tool for a task it is not designed to perform.pp WARNING! DO NOT use the tool if damaged or faulty. Contact your local service agent.7 DO NOT use the tool unless you have been instructed in its use by a qualified person.7 DO NOT carry the tool by the air hose, or yank the hose from the air supply.7 DO NOT direct air from the air hose at yourself or others.7 DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating medication.3 When not in use, disconnect from air supply and store in a safe, dry, childproof location.SA36.V2 - 1 -290802Model: SA36.V201284 757500 E-mail: sales@sealey.co.ukWeb: www.sealey.co.uk01284 703534NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and componentparts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12months from purchase date. proof of which will be required for any claim. INFORMATION: Call us for a copy of our latest catalogueand promotions on 01284 757525 and leave your full name and address including your postcode.Sole UK Distributor, Sealey Group, Bury St. Edmunds, Suffolk.Issue: 1Date Issue: 290802Item Part No. Description1 SA36.V2-01 Clamp2 SA36.V2-02 Set Screw3 SA36.V2-03 Punch Die4 SA36.V2-04 Guide Bushing5 SA36.V2-05 Cup Spring6 SA36.V2-06 Punch7 SA36.V2-07 Screw8 SA36.V2-08 Cover Plate9 SA36.V2-09 Anvil10 SA36.V2-10 Oil Seal11 SA36.V2-11 Support Ring12 SA36.V2-12 O-ring13 SA36.V2-13 Oil Plug14 SA36.V2-14 O-ring15 SA36.V2-15 Hydraulic Cylinder16 SA36.V2-16 Air Cylinder17 SA36.V2-17 Plastic Wrap18 SA36.V2-18 Valve BodyItem Part No. Description19 SA36.V2-19 Air Inlet20 SA36.V2-20 Throttle Lever21 SA36.V2-21 Spring Pin22 SA36.V2-22 O-ring23 SA36.V2-23 Push Rod24 SA36.V2-24 Spring25 SA36.V2-25 Valve26 SA36.V2-26 Spring27 SA36.V2-27 O-ring28 SA36.V2-28 Screw29 SA36.V2-29 O-ring30 SA36.V2-30 Support Ring31 SA36.V2-31 Hydraulic Piston32 SA36.V2-32 O-ring33 SA36.V2-33 Support Ring34 SA36.V2-34 Spring35 SA36.V2-35 Piston36 SA36.V2-36 O-ringINSTRUCTIONS FORAIR PUNCH/FLANGE TOOL2. INTRODUCTION & SPECIFICATIONNoise . . . . . . . . . . . . . . . . . .81.7dB(A)Spare Punch . . . . . . . . . . . . .SA36/36Spare Die . . . . . . . . . . . . . . . SA36/40Operating Pressure . . . .90psi (6.2 bar)Air Inlet . . . . . . . . . . . . . . . . . 1/4îBSPWeight . . . . . . . . . . . . . . . . . . . . 1.3kgVibration . . . . . . . . . . . . . . . . .<2.5m/s22.1. IntroductionSuitable for heavy bodyshop use. Aluminium alloy body with steel punch and die. Puts a 10mm flangeonto car-panel-thickness sheet for lap jointing and puts 6mm holes in panels for mig spot-welding.2.2. Specification

/ 2

Related manuals for Sealey Power Tools SA36.V2