Sealey MIG/LITE Instructions Manual

INSTRUCTIONS FOR:ELECTRONIC WELDING HEADSHIELDModel No: MIG/LITEThank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.3 Maintain the helmet in good condition (use an authorised service agent).3 Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.3 The helmet has two independent photo sensors which must be free of dust and debris.3 Always use the helmet with an anti-spatter cover len installed to protect it from weld splatter3 For optimum results, use your MIG/LITE helmet between the temperatures of -5 0 C (+230 F) and + 55 0 C (+1310 F).3 Use helmet and filter for eye/face protection against harmful ultraviolet and infrared radiation sparks and splatter from welding and cutting.3 The protective plate in this helmet is NOT unbreakable. The helmet will not protect you against severe impact hazards (such as, but not limited to)fragmenting abrasive discs and grinding wheels, stones and other grinding tools, explosive devices or corrosive fluids. Appropriate eye protection must be usedwhere these hazards exist.3 Ensure all workshop safety rules, regulations, and conditions are complied with when using welding equipment. The helmet will not offer protection againstmis-use of workshop tools, equipment, or accessories.3 Remove ill fitting clothing, remove ties, watches, rings, and other loose jewellery.3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.3 Keep children and unauthorised persons away from the working area.3 Maintain helmet batteries in good condition. Low power indicator operates when 8 hours or less of life is left.7 DO NOT use helmet unless you have been instructed in its use by a qualified person.7 DO NOT get the helmet wet or use in damp or wet locations.3 When not in use switch the light sensor off, and store the helmet in a safe, dry, childproof area.1. SAFETY INSTRUCTIONSThe MIG/LITE autodarkening welding helmet offers personal eye and face protection during welding. The helmet is fully adjustable to fit over your head. The helmetautomatically darkens in less than 0.1 milliseconds when arc is struck, allowing you to see more easily during positioning. The shade varies from 9 to 12 which suitsmost gas and mig welders. Variable sensitivity allows for use outdoors. A variable delay on return to clear allows for use when spot welding. The unit is powered bytwo AA 1.5 Volt batteries.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS ANDCAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAYCAUSE DAMAGE, OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE2. SPECIFICATIONS & TECHNICAL DATAThe Helmet.Manufactured by plastic injection incorporating materials of 10% glass thermoplastic compound (Norylgeneral Electric Plastic).The Headgear.The headgear is made of thermoplastic compounds incorporating: Polyamide, Polyethylene, and Polypropylene. The helmet has a removable hygienic foam browpad. All materials being hypoallergenic.The Autodarkening Welding Filter:Filter size ...................................1 1/2 x 3 3/4Switching time ...........................<0.1ms (0.1 millisecond = 0.0001 second) at -50 C<0.1ms (0.1 millisecond = 0.0001 second) at +230 C<0.1ms (0.1 millisecond = 0.0001 second) at +550 CDensity ................................1.16Electrical insulation .............0.07 mAHeat Resistance..................240 0 CProvides permanent full protection against UV and IR radiation in ON and OFF modes.Protection level against visible radiation: OFF State.........Transmission factor 7. ON State........Transmission factor 4 without arc (light mode).Transmission factor continuously adjustable from 9 to 12 when the arc is on (dark mode).Arc detection by 2 independent light sensors.Delay between dark mode and light mode continuously adjustable from 0.1 second to 1 second.Sensitivity to arc light continuously adjustable.If helmet is left on it will automatically switch off after 28 minutes.Battery life of approximately 700 hours in ON mode. Red light warning indicator starting approximately 8 hours before batteries fail.Powered by 2 x AA size 1.5 Volt alkaline batteries.The Anti-Splatter Cover Lenses.Made with a methyl-methacrylat compound.Perfect optical quality.............................................................(DIN EN 166 No. 47198 PTB 92).Total weight complete with headgear and batteries ...............548 grams.MIG/LITE - 213 -170398The helmet has a shade selector knob for proper shade selection. Refer to the following chart for shade recommended for yourapplication.3. CHARACTERISTICS

/ 2

Related manuals for Sealey MIG/LITE