Sealey IR3000.V2 Instructions Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY1.1. Electrical Safety WARNING! It is the owner’s responsibility to read, understand and comply with the following:You must check all electrical equipment and appliances to ensure that they are safe before use. You must inspect power supply leads, plugs andall electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safetydevices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged intoan electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by contactingyour Sealey dealer. You must also read and understand the following instructions concerning electrical safety.1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested bya qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the applianceand the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.1.1. & 1.1.2. aboveand use a Portable Appliance Tester (PAT).1.1.4. Ensure that cables are always protected against short circuit and overload.1.1.5. Regularly inspect power supply, leads, plugs for wear and damage and all electrical connectionsto ensure that none is loose.1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supplyto be used and check that supply is correctly fused, see fuse rating at right.1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.1.1.8. DO NOT pull power plugs from sockets by the power cable.1.1.9. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have repairedby a qualified electrician.1.1.10. This product comes without a plug. You must contact a qualified electrician to ensure an adequatesupply is available.If fitting such a plug -Ensure that the unit is correctly wired and earthed, as follows:a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.b) Connect the BROWN live wire to live terminal ‘L’.c) Connect the BLUE neutral wire to the neutral terminal ‘N’.d) After wiring, check there are no bare wires, that all wires have been correctly connected,that the cable outer insulation is clamped by the cable grip and that the grip is tight.1.1.11. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCDfitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cores of the cable isimportant. 2.5mm² section is a minimum, but to be absolutely sure that the capacity of the cable reel is suitable for this product andfor others that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.1.2. General Safety WARNING! Ensure there is nobody in front of the lamp when it is switched on.9 Disconnect the panel dryer from the power supply before servicing, changing accessories, or performing any maintenance.9 Ensure that the panel dryer is in good condition before use. If in any doubt do not use the unit and contact an electrician.9 Familiarise yourself with the application and limitations of the panel dryer.9 Check that lamp guards are in place, undamaged and firmly attached.9 Keep tools and other items away from the panel dryer when it is in use.9 Keep the work area clean and clear of unnecessary items.9 Remember that the lamp panel will get hot, allow to cool after use.9 Maintain the panel dryer in good condition. Use authorised agent for servicing.9 Keep the dryer clean, but DO NOT use solvents.9 Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate yourwarranty.8 DO NOT use this product to perform a task for which it has not been designed.8 DO NOT use the panel dryer outdoors, or in damp, or wet locations, and DO NOT operate within the vicinity of flammable liquids, gases orsolids. WARNING! Never use in explosive situations.IndoorUse OnlyIR3000.V2| Issue 1 06/09/16Original Language Version© Jack Sealey LimitedINSTRUCTIONS FOR:SHORT WAVE INFRARED PANEL DRYERMODEL NO: IR3000.V2Refer toInstructionManualWarning:ElectricityWarning:Hot SurfaceTHIS PRODUCT REQUIRES AMINIMUM 16 AMPSUPPLY