Sealey HVLP04 Manual

Touch-up Spray Gun profeSSionalGraviTy feed hvlp 1mm SeT-upModel no: hvlp04Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.imporTanT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SafeTy WarninG! disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.9 Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the spray gun.Paint cup remains pressurised after gun is disconnected from air line.8 do noT pull the trigger, but release the pressure by gently opening cup.9 Maintain the spray gun in good condition (use an authorised service agent). Replace or repair damaged parts.9 Use recommended parts only. non authorised parts may be dangerous and will invalidate the warranty.9 locate the spray gun in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, andensure there is adequate ventilation and lighting.9 Keep the spray gun clean for best and safest performance.9 Ensure the air system is suitable to the spray gun air consumption, (see specifications).9 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and tie back long hair.9 Keep children and unauthorised persons away from the working area.8 do noT point spray gun at yourself, at other persons or animals.8 do noT carry the by the air hose, or pull the hose from the air supply.8 do noT use the spray gun for any purpose other than for which it is designed.8 do noT allow untrained persons to operate the spray gun.8 do noT get the spray gun wet or use in damp or wet locations or areas where there is condensation.8 do noT operate gun if any parts are missing or damaged as this may cause failure or personal injury.8 do noT direct air from the air hose at yourself or others.9 Avoid unintentional operation. When not in use switch the spray gun off, and disconnect from the air supply.2. inTroducTionProfessional gravity feed spray gun with 1mm set-up, ideal for blowing-in small areas of panel where fine control of paint and air is necessary.Features air and paint flow controls for fine adjustment of spray pattern. HVLP Technology and precision engineering delivers consistent andunrivalled results. Brass air cap with stainless steel needle and nozzle suitable for water based paints. Alternative set-up available separately.3. SpecificaTionModel no: .................................................................HVLP04Air Consumption: ........................................................... 7cfmAvailable Set-Up(s): .................................................... 0.8mmnett Weight: ................................................................ 0.52kgPot Capacity: ............................................................... 100mlRecommended Air Pressure: ........................................ 22psiStandard Set-Up: ........................................................... 1mm4. conTenTS1.Spanner .......................................................................... x12.Cleaning Brush................................................................ x13.Strainer ........................................................................... x14.Screwed Adaptor- Female thread .................................... x15.Spray Gun ....................................................................... x15. aSSembly5.1. empty contents from the product carton on to a tray or bench. In the unlikely eventof missing or damaged parts, inform your Sealey stockist immediately.5.2. The spray gun has been treated with an anti corrosive agent at the factory and MUST be flushed out thoroughly before use.5.3. Ensure the strainer, item 3 fig.1, is inserted into the gun port with the stem outermost for easy removal.5.4. Fit the pot and selected spray head, hand tight only.1. 2.3.4.fig.1HVLP04 Issue 1 11/01/19Original Language Version© Jack Sealey limitedRefer toinstructionsWear eyeprotectionWear protectiveglovesWear protectiveclothingWearrespiratoryprotectionWear safetyfootwear

/ 3

Related manuals for Sealey 5054511589658