Sealey DPF1 Manual

DPF ULTRA CLEANING STATIONMODEL NO: DPF1Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY1.1. ELECTRICAL SAFETYWARNING! It is the user’s responsibility to check the following:Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and allelectrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electricalproducts. You may obtain an RCD by contacting your local Sealey stockist.If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (PortableAppliance Test) tested.ELECTRICAL SAFETY INFORMATION: it is important that the following information is read and understood.1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.1.1.3. IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with thecorrect fuse - see fuse rating in these instructions.8 DO NOT pull the appliance by the power cable.8 DO NOT pull the plug from the socket by the cable.8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired orreplaced immediately by a qualified electrician.1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.If the cable or plug is damaged during use, switch the electricity supply and remove from use.Ensure that repairs are carried out by a qualified electrician.Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.B) Connect the BROWN live wire to the live terminal ‘L’.C) Connect the BLUE neutral wire to the neutral terminal ‘N ’.Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.Sealey recommend that repairs are carried out by a qualified electrician.1.2. GENERAL SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using thisunit.9 Wear appropriate PPE.9 Familiarise yourself with the applications, limitations and potential hazards of the unit. WARNING: Only use in well ventilated areas. Exhaust gases are poisonous.9 Operators must receive adequate training before using the unit.9 Always perform automotive work in a safe environment.8 DO NOT operate the unit while under the influence of drugs, alcohol or intoxicating medication, or if tired.8 DO NOT cover the unit or place heavy loads on top of it.8 DO NOT operate in wet or damp conditions.9 Check the condition and operation of all components before each use.9 Operate the unit on a smooth level surface in order to avoid tipping or spillage.9 Stand correctly keeping a good footing and balance, ensure that the floor is not slippery and wear non-slip shoes.9 Keep unauthorised persons away from the work area. Any persons working within the area must wear the same protective items.9 Keep the unit, hoses and cables in good working order and condition. Take immediate action to repair or replace damaged parts.2. INTRODUCTIONProvides an off-vehicle, same day workshop cleaning solution. The machine uses a mixture of high pressure air, chemicals and water. Thiscleaning station along with the Sealey recommended chemicals offers a fast and cost effective way to completely clean and protect any DPF.Great revenue boost for any workshop. Each treatment will require a DPF Ultra Cleaning Kit (Model No. DPF1KIT) which includes 1 x UltraClean and 1 x Ultra Protect Solution. The ultra cleaning chemical is a unique solution specially formulated to safely lift impurities from the DPF.The protect chemical features the latest nano catalyst technology to keep your DPF cleaner for longer. Also features an automatic servicefunction allowing the user to continue with other work.Replacement fuserating: 13ADPF1 Issue 2 (5) 23/09/20Original Language Version© Jack Sealey LimitedRefer toinstructionsWear a faceshieldWear protectiveglovesWear safetyfootwearWarningElectricityKeep out of rain High pressureair hazard

/ 4

Related manuals for Sealey DPF1