Sealey DDE01 Instructions Manual

3V Vacuum Drill Dust ExtractorModel no: DDE01thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.importaNt: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. safEty1.1. GENEral safEty.8 Do Not use this device in direct sunlight.8 Do Not allow the dust extractor to get wet.8 Do Not allow unqualified persons or children to operate this device.1.2. lasEr safEty. The dde01 utilises a Class II laser that emits a low level of visible radiation(i.e. a wavelength of 650 nanometres) which is safe for the skin but not inherently safe for the eyes.The Class II emission limit is set at the maximum level for which eye protection is normally affordedby natural aversion responses to bright light. Accidental eye exposure is therefore normally safe,although the natural aversion response can be overridden by deliberately staring into the beam,and can also be influenced by the use of alcohol or drugs.8 Do Not direct the laser beam at any person’s (or animal’s) eyes as eye damage could result.8 Do Not operate the laser level when you are tired or under the influence of alcohol, drugs orintoxicating medication. Be aware that reflections of the laser beam from mirrors or othershiny surfaces can be as hazardous as direct eye exposure.2. iNtroDuctioN3V Vacuum holds unit to the wall for easy drilling. Suitable for drill bits up to 13mm. Features a horizontal and vertical spirit level for accuratepositioning. Laser light on the bottom for accurately positioning of holes, for example in a sequence or a square. Removable dust collectionpod for easy emptying. Powered by 2 x AA Batteries (not included).3. spEcificatioNmodel No:...................................................................DDE01Maximum drilling diameter: ......................................... 13mmnett Weight: ................................................................ 0.24kg4. opEratioNNotE: The vacuum seal on this product is only suitable for smooth conformingsurfaces.4.1. DrilliNG a holE4.1.1. Mark position of hole that you want to drill. If drilling more than onehole in succession the laser guides can be used to line up with yourmarkings (fig.1).4.1.2. There is a small gap in the bristles on-top of the device that allow youto see your prepared markings. Line up your mark with this hole. Youcan also use the lasers and spirit levels to help with this.4.1.3. When happy with your placement turn on the suction (fig.2). The devicewill now be stuck to the wall. The vacuum can be released usingthe button on the side of the body (fig.2).4.2. EmptyiNG thE collEctor4.2.1. The device can be slid apart leaving you with two pieces. The dustcollection pod and the suction device (fig.3).4.2.2. The dust collection pod comes apart by gently pressing the tabs onthe sides. Once apart the dust should be safely disposed of.NotE: The dust is collected via gravity and not suction.4.3. chaNGiNG thE battEriEs4.3.1. Lift the cover of the body up using the tab under the laser.4.3.2. Wiggle the cover free, being careful not to damage the locatingpins on the opposite side of the cover.fig.1CompressorOn/OffLaser On/OffVacuumReleaseSpirit LevelsDust CollectionPodfig.2fig.3dDE01 Issue 1 04/03/19Original Language Version© Jack Sealey limitedRefer toinstructionsWarning laserWear eyeprotectionWear a mask

/ 2

Related manuals for Sealey 5054511621051