Sealey DAS150T.V6 Manual

Also see for DAS150T.V6: Instructions

Ø150MM DUAL ACTION VARIABLE SPEEDSANDER 710WMODEL NO: DAS150T.V6Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY1.1. ELECTRICAL SAFETY WARNING! It is the user’s responsibility to check the following:Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs andall electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electricalproducts. You may obtain an RCD by contacting your local Sealey stockist .if the used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test)tested.Electrical safety information, it is important that the following information is read and understood.9 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.9 Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.9 Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - seefuse rating in these instructions.8 DO NOT pull or carry the appliance by the power cable.8 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by aqualified electrician.This product is fitted with a BS1363/A 13 Amp 3 pin plug.If the cable or plug is damaged during use, switch off the electricity supply and remove from use.Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;A) Connect the BROWN live wire to the live terminal ‘L’.B) Connect the BLUE neutral wire to the neutral terminal ‘N’.C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.DO NOT connect either wire to the earth terminal.Sealey recommend that repairs are carried out by a qualified electrician.1.2. GENERAL SAFETY WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using thisequipment. WARNING! Disconnect from mains power before changing accessories or servicing.9 Maintain the sander in good condition (use an authorised service agent).9 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.9 Use the sander in a suitable work area. Keep area clean, tidy and free from unrelated materials. Ensure that there is adequate lighting9 Before use, check abrasive pad condition. If worn or damaged replace immediately. WARNING! Always wear approved eye or face, ear, hand protection when operating the sander. Always wear a mask.9 Wear respiratory protection in accordance with COSHH regulations.9 Remove ill fitting clothing, ties, watches, rings, other loose jewellery and contain and/or tie back long hair.9 Wear appropriate protective clothing and keep hands and body clear of moving parts.9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.9 Keep children and unauthorised persons away from the work area.9 Always use the sander with the side handle securely screwed in.9 Ensure the workpiece is correctly secured before operating the sander. Never hold workpiece by hand and check the workpiece toensure there are no protruding nails, screws, rivets, etc.9 Avoid unintentional starting.8 DO NOT use the sander for a task it is not designed to perform.8 DO NOT operate the sander if any parts are damaged or missing. This may cause failure and/or injury.Original Language Version© Jack Sealey LimitedRefer toinstructionsWear eyeprotectionWear protectiveglovesWear earprotectionWear safetyfootwearWear protectiveclothingWear a maskRecommended fuse rating3 AmpDAS150T.V6 Issue 1 11/08/20

/ 4

Related manuals for Sealey DAS150T.V6