Sealey CP36B.V2 Manual

26PC 3.6V CORDLESS SCREWDRIVER SETMODEL NO: CP36B.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY1.1. GENERAL SAFETY9 Maintain the screwdriver in good condition. Check moving parts alignment on a regular basis.9 Keep the screwdriver and charger clean for best and safest performance.9 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.9 Secure loose workpieces with a clamp, vice or other adequate holding device.9 Avoid unintentional starting.9 Wear approved safety eye protection.9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.9 Keep children and unauthorised persons away from the working area.8 DO NOT allow children to operate the screwdriver.8 DO NOT hold unsecured workpiece in your hand.8 DO NOT carry the screwdriver with your finger on the trigger.8 DO NOT use the screwdriver for a task it is not designed for.8 DO NOT operate the screwdriver when you are tired or under the influence of alcohol, drugs or intoxicating medication.8 DO NOT get the screwdriver or battery charger wet or use in damp or wet locations.9 Keep screwdriver and charger in a safe, dry, child proof area where the temperature will not exceed 104°F (40°C).1.2. ELECTRICAL SAFETY FOR USE OF CHARGERUSE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING SCREWDRIVER TO THE POWER SUPPLY. WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual CurrentCircuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device)is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by anRCCB. You must also read and understand the following instructions concerning electrical safety.1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by aqualified electrician, using a Portable Appliance Tester (PAT), at least once a year.1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of theappliance and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.1.2.3. You must ensure that you:9 Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains powersupply. If worn or damaged DO NOT use.IMPORTANT: Check that the voltage marked on the charger plug is the same as the power supply to be used.8 DO NOT pull the charger plug from the mains socket by the lead.8 DO NOT use any other type of charger with this product.8 DO NOT try to take the charger plug apart.8 DO NOT use the charger plug to charge or power any other electrical item.8 DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only). WARNING! NEVER substitute a standard 13amp 3 pin plug, or any other type of plug, for the charger plug.1.3. BATTERY SAFETY WARNING! To reduce the risk of burns or fire:8 DO NOT attempt to open, dismantle, modify or service the battery.8 DO NOT crush, puncture, short external contacts or dispose of in fire or water. DO NOT expose to temperatures above 60°C (140°).9 Recycle or dispose of used battery as stipulated by local regulation.2. INTRODUCTIONCompact, lightweight and comfortable to use. Features locking swivel adjustment from pistol to straight grip. Forward, reverse and trigger-lockwith soft grip handle. Features LED work light and three colour battery indicator. Eight adjustable torque settings coupled with a quick releasebit holder. Supplied with 24 assorted bits and mains charging cable.CP36B.V2 Issue 2(3) 28/09/2021Original Language Version© Jack Sealey LimitedRefer toinstructionsWear eyeprotection

/ 3

Related manuals for Sealey CP36B.V2