Sealey CP20VCS Instructions Manual

20V CirCular Saw Ø150mm - Body onlyModel no: CP20VCSThank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.imPorTanT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SafeTy1.1. General SafeTy warninG! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using thisequipment. warninG! do noT aim the laser beams at your or another person’s or animal’s eye and beware of reflections from mirrors or othershiny surfaces.9 Remove the battery from the saw before changing blades, servicing or performing any maintenance.9 Maintain the saw in good condition. Check moving parts alignment on a regular basis.9 Replace or repair damaged parts. Use an authorised service agent and use recommended parts only. Unauthorised parts may bedangerous and will invalidate the warranty.9 Keep the saw clean and the blade sharp for best and safest performance.9 Wear approved safety eye protection (standard spectacles are not adequate) and dust mask.9 Maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.9 Keep children and unauthorised persons away from the working area.9 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.9 Use in a suitable work area. Keep area clean, tidy and free from unrelated materials. ensure there is adequate lighting.9 ensure locking hex. key is removed from the blade clamp flange before starting saw.9 evaluate your work area before using the saw e.g. partitions may conceal electric cables or water piping.9 Secure non-stable workpiece with a clamp, vice or other adequate holding device.9 Avoid unintentional starting.9 Before making a cut ensure that all accessories and adjustment fixings are fully tightened.9 only use saw blades that are specifically designed for use with this machine.9 Always use the side fence supplied or a securely fixed straight edge guide when doing a rip cut (along the length of the grain).9 When not in use store in a safe, dry, childproof area .8 do noT use the saw where there are flammable liquids, solids or gases such as paint solvents, etc.8 do noT allow children to operate the saw.8 do noT operate the saw if any parts are missing as this may cause failure and/or personal injury.8 do noT leave the saw operating unattended.8 do noT carry the saw with your finger on the power switch.8 do noT use the saw for a task it is not designed to perform.8 do noT use a blade which is damaged, cracked, distorted or has missing teeth.8 do noT tamper with, or remove, blade guard.8 do noT operate the saw when you are tired, under the influence of alcohol, drugs or intoxicating medication.8 do noT get the saw wet or use in damp or wet locations.8 do noT hold unsecured workpiece in your hand whilst cutting.8 do noT force the saw to cut but allow it to operate at its normal working speed.8 do noT use the saw with any other manufacturers’ accessories.8 do noT reach under the workpiece whilst the blade is cutting. Keep hands away from the cutting area and do not attempt to removecut material whilst the blade is still turning.8 do noT wedge the blade guard open.8 do noT fit or use a saw blade that is intended to cut metal. Always ensure that the saw is fitted with the correct wood cutting blade.8 do noT substitute an abrasive wheel for the saw blade.8 do noT allow the blade to come into contact with nails or other steel fixings used in old timber or existing timber structures. Inspect theworkpiece before commencing cutting and remove any potential hazards.8 do noT attempt to stop the saw by pressing on the side of the blade.8 do noT start the saw with the blade in contact with the workpiece. Allow the blade to run up to speed before proceeding to cut.1.2. laSer SafeTy warninG! do noT look or stare into the laser beam as permanent eye damage could result.The CP20VCS utilises a Class II laser that emits low levels of visible radiation (i.e. wavelengths between 400 and 700 nanometres)which are safe for the skin but not inherently safe for the eyes. The Class II emission limit is set at the maximum level for which eyeprotection is normally afforded by natural aversion responses to bright light.Original Language Version© Jack Sealey limitedRefer toinstructionsWear eyeprotectionWear protectiveglovesWear earprotectionWear safetyfootwearWear protectiveclothingCP20VCS Issue 1 17/09/19Warning!laser beamWeardust mask

/ 5

Related manuals for Sealey CP20VCS