Sealey CP1201 Instructions Manual

Also see for CP1201: Manual Manual

instructions forHammer drill / driver 12v 10mm-bodyonlymodel no: CP1201Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SafeTy1.1. eleCTriCal SafeTy. WarninG! it is the owner’s responsibility to read, understand and comply with the following electrical instructions:9 You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An rccB (residual currentcircuit Breaker) should be incorporated in the main distribution board. We also recommend that an rcd (residual current device)is used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by anrccB.9 You must also read and understand the following instructions concerning electrical safety.the electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualifiedelectrician, using a Portable Appliance tester (PAt), at least once a year.the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance andthe safety of the appliance operator.if in any doubt about electrical safety, contact a qualified electrician.9 ensure that the charger and cable are inspected for wear and damage, to ensure they are safe before connecting to the mains powersupply. if worn or damaged do noT use, replace immediately or contact a qualified electrician.8 do noT use worn or damage cables, plugs or connectors. Have any faulty item repaired or replacedimmediately by a qualified electrician. When an AstA/Bs approved uK 3 pin plug is damaged, cutthe cable just above the plug and dispose of the plug safely.9 ensure that the double insulated charger is correctly connected via a three-pin plug, as follows:a) connect the Brown live wire to live terminal ‘l’.b) connect the Blue neutral wire to the neutral terminal ‘n’.c) After wiring, check that there are no bare wires, that all wires have been correctly connected,that the cable outer insulation extends past the cable clamp and that the clamp is tight.note that the earth pin ‘e’ remains unconnected.9 check cables are always protected against short circuit and overload.9 baTTery SafeTy. (Battery cP1200BP / charger cP1200mc not supplied)9 Charge battery prior to first use. The battery pack will have been shipped in a low charge state.9 use only the charger provided to charge the drill battery.8 do noT charge battery when room temperature is below 50°f (10°c) or above 104°f (40°c).8 do noT attempt recharging the battery by means of a generator or a dc power source.8 do noT short-circuit the battery by linking both terminals with conductive materials.8 do noT store the battery (or drill) in locations where the temperature may exceed 104°f (40°c).▲ danGer! do noT attempt to dismantle the battery pack. for safety and environmental reasons do noT discard in domesticwaste or by burning. onlY discard or recycle according to local authority regulations. WarninG! do noT allow a leaking battery to contact your person. if you come into contact with battery liquid take the followingimmediate action:a) skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.b) eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.1.2. baTTery CHarGer SafeTy inSTruCTionS. (Battery cP1200BP / charger cP1200mc not supplied) WarninG: do noT use the charger to charge any battery other than that supplied for the drill. other types of batteries mayexplode.9 All mains electrical supply safety features must be followed as described in 1.1. above.9 disconnect the charger from the mains power supply when not in use.9 important: check that the voltage marked on the charger is the same as the power supply to be used.8 do noT pull or carry the charger by the power lead, or pull the plug from the mains socket by the power lead.8 do noT use any other type of charger.8 do noT try to open or dismantle the charger.8 do noT get the charger wet, or use in wet, damp conditions (for indoor use only).8 do noT operate the charger if it or the battery is damaged.cP1201 | issue2(sP) 30/08/17Original Language Version© Jack sealey limitedrefer toinstructionsWear eyeprotectionWear protectiveglovesWear earprotectionCharger: indooruse onlyrecommended fuserating: 3a

/ 3

Related manuals for Sealey CP1201