Menu
Sealey AUTO SERVICE VS209.V2 Instructions Manual
  |
INSTRUCTIONS FOR:CaRbUReTTOR SyNChRONIzeRModel No: VS209.V21. SaFeTy INSTRUCTIONSOne of the most comprehensive balancer sets available on the market. Features a bank of four mini-gauges withlockable valves enabling user to hold vacuum values in use. Supplied with set of long and short carburettoradaptors for easy access amongst the tubes and wires around the carburettor. Includes four 900mm deliverytubes. Supplied in carry-case.2. INTRODUCTION Ensure that Health & Safety, local authority and general workshop practice regulations are strictly adhered towhen using tools. Maintain the equipment in good and clean condition for best and safest performance. DO NOT use ifdamaged. Wear approved eye protection. A full range of personal safety equipment is available from your Sealeydealer.8 DO NOT use the equipment for purposes other than for which it is designed.8 DO NOT use the equipment when you are tired or under the influence of alcohol, drugs or intoxicatingmedicine. Wear suitable clothing to avoid snagging. Do not wear loose jewellery and tie back long hair. Account for all tools and parts being used and do not leave them in, on or near the engine. Ensure that work area has adequate lighting. Keep children and unauthorised persons away from work area. When not in use, store the equipment in a safe, dry childproof area. IMPORTaNT: Refer to the vehicle manufacturer’s service instructions, or a proprietory manual, to establishthe correct procedure and data. These instructions are provided as a guide only. IMPORTaNT: Ensure the vehicle has been serviced and that the air screw and pilot screw have beencorrectly adjusted. WaRNING! exhaust fumes are dangerous, ensure steps are taken to remove fumes from work area. WaRNING! It is assumed that anybody using the VS209 will have some knowledge of the mechanics of thevehicle, particularly in regard to safe handling of fuel systems and removal of the fuel tank. If there is anydoubt refer the job to a professional mechanic.3. INSTRUCTIONS FOR USeThank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.IMPORTANT: PLeaSe ReaD TheSe INSTRUCTIONS CaReFULLy. NOTe The SaFe OPeRaTIONaL ReQUIReMeNTS, WaRNINGS aNDCaUTIONS. USe ThIS PRODUCT CORReCTLy, aND WITh CaRe FOR The PURPOSe FOR WhICh IT IS INTeNDeD. FaILURe TO DO SO MayCaUSe DaMaGe aND/OR PeRSONaL INJURy aND WILL INVaLIDaTe The WaRRaNTy.fig.1Release valveOriginal Language Version VS209.V2 Issue: 1 - 15/04/113.1 SeT-UP3.1.1 Start the vehicle and run until it will operate without choke. When this has beenachieved, turn off the engine and fit the vacuum gauges as follows:3.1.2 Remove the inlet manifold vacuum screw(s). Select the appropriate extensionconnector and screw into the inlet manifold of vehicle, do not overtighten,finger pressure is adequate.3.1.3 Repeat for the remaining carburettors (up to four).3.1.4 Push fit the rubber hose to each extension connector ensuring a good fit so no airwill leak.3.1.5 Push fit the other end of the hose to the gauges ensuring a good fit so no air will leak.3.2 OPeRaTION3.2.1 Close the lockable valves (fig.1) and start the engine.3.2.2 Open each regulator gradually by turning the lockable valves (fig.1) until the display needle stabilises.3.2.3 Refer to the vehicle handbook for slide adjustments to the carburettors. Following the vehiclehandbook, make the adjustments to each carburettor until all the display readings are the same.3.2.4 Advance the throttle a few times and allow the engine to settle back to tickover. You can close thelockable valves to hold vacuum values in use. Re-check the display readings and confirm they are stillreading the same values. If not re-adjust the carburettors as necessary.3.2.5 When synchronization is complete, switch off engine and remove extension connectors from themanifold. Replace the vacuum screw(s) back into the inlet manifold.INSTRUCTIONS FOR:CaRbUReTTOR SyNChRONIzeRModel No: VS209.V21. SaFeTy INSTRUCTIONSOne of the most comprehensive balancer sets available on the market. Features a bank of four mini-gauges withlockable valves enabling user to hold vacuum values in use. Supplied with set of long and short carburettoradaptors for easy access amongst the tubes and wires around the carburettor. Includes four 900mm deliverytubes. Supplied in carry-case.2. INTRODUCTION Ensure that Health & Safety, local authority and general workshop practice regulations are strictly adhered towhen using tools. Maintain the equipment in good and clean condition for best and safest performance. DO NOT use ifdamaged. Wear approved eye protection. A full range of personal safety equipment is available from your Sealeydealer.8 DO NOT use the equipment for purposes other than for which it is designed.8 DO NOT use the equipment when you are tired or under the influence of alcohol, drugs or intoxicatingmedicine. Wear suitable clothing to avoid snagging. Do not wear loose jewellery and tie back long hair. Account for all tools and parts being used and do not leave them in, on or near the engine. Ensure that work area has adequate lighting. Keep children and unauthorised persons away from work area. When not in use, store the equipment in a safe, dry childproof area. IMPORTaNT: Refer to the vehicle manufacturer’s service instructions, or a proprietory manual, to establishthe correct procedure and data. These instructions are provided as a guide only. IMPORTaNT: Ensure the vehicle has been serviced and that the air screw and pilot screw have beencorrectly adjusted. WaRNING! exhaust fumes are dangerous, ensure steps are taken to remove fumes from work area. WaRNING! It is assumed that anybody using the VS209 will have some knowledge of the mechanics of thevehicle, particularly in regard to safe handling of fuel systems and removal of the fuel tank. If there is anydoubt refer the job to a professional mechanic.3. INSTRUCTIONS FOR USeThank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properlymaintained, give you years of trouble free performance.IMPORTANT: PLeaSe ReaD TheSe INSTRUCTIONS CaReFULLy. NOTe The SaFe OPeRaTIONaL ReQUIReMeNTS, WaRNINGS aNDCaUTIONS. USe ThIS PRODUCT CORReCTLy, aND WITh CaRe FOR The PURPOSe FOR WhICh IT IS INTeNDeD. FaILURe TO DO SO MayCaUSe DaMaGe aND/OR PeRSONaL INJURy aND WILL INVaLIDaTe The WaRRaNTy.fig.1Release valveOriginal Language Version VS209.V2 Issue: 1 - 15/04/113.1 SeT-UP3.1.1 Start the vehicle and run until it will operate without choke. When this has beenachieved, turn off the engine and fit the vacuum gauges as follows:3.1.2 Remove the inlet manifold vacuum screw(s). Select the appropriate extensionconnector and screw into the inlet manifold of vehicle, do not overtighten,finger pressure is adequate.3.1.3 Repeat for the remaining carburettors (up to four).3.1.4 Push fit the rubber hose to each extension connector ensuring a good fit so no airwill leak.3.1.5 Push fit the other end of the hose to the gauges ensuring a good fit so no air will leak.3.2 OPeRaTION3.2.1 Close the lockable valves (fig.1) and start the engine.3.2.2 Open each regulator gradually by turning the lockable valves (fig.1) until the display needle stabilises.3.2.3 Refer to the vehicle handbook for slide adjustments to the carburettors. Following the vehiclehandbook, make the adjustments to each carburettor until all the display readings are the same.3.2.4 Advance the throttle a few times and allow the engine to settle back to tickover. You can close thelockable valves to hold vacuum values in use. Re-check the display readings and confirm they are stillreading the same values. If not re-adjust the carburettors as necessary.3.2.5 When synchronization is complete, switch off engine and remove extension connectors from themanifold. Replace the vacuum screw(s) back into the inlet manifold. |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved